Thule base for 835XTR Part No. 853-5303

Question

Question:

I see you carry the base pad part no, 853-5302. Do you also carry the base part no. 853-5303? Need to replace both parts. This is for Thule 835XTR Hull-A-Port rack. Thank you.

asked by: Gayle E

0

Expert Reply:

We do indeed carry the Thule 853-5303, only we refer to it as part # TH96JV.

expert reply by: Mike L

0

Answer 1

I understand your concern about your Thule Hull-A-Port Kayak Carrier #TH834 coming loose from your vehicle roof rack crossbars but I cannot recommend using any alternate hardware (such as that from another Thule carrier). What I suggest you do is…

view full answer...

Answer 2

You certainly can get replacement pads for the Thule Hull-A-Port PRO. To replace the bottom tube pad, you will want to use the Thule Replacement 6 Inch Pad #853-5540. For the upper arm's tube pads, you will want #8537418. To replace the bottom…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

Hi Alec, The Inno Kayak Roof Rack w/ Tie-Downs #INA452 needs a 28" minimum spread so that the saddles sit at the right spot for the kayak and support the weight properly. This is probably just a general guide from Inno though because the length…

view full answer...

Answer 10

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Thule base for 835XTR Part No. 853-5303

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching