Installation of the Curt Class III Trailer Hitch # C13128 on a 2012 Range Rover Evoque Dynamic
Question:
Hello I saw your response to one of your customers from this web site: http://www.etrailer.com/question-47900.html I saw a picture of an Evoque and it was for a round exhaust. How about for the square exhaust such as the Evoque Dynamic? Thanks
asked by: Alvin
Expert Reply:
I spoke with my contact at Curt and he assured me that the installation of the Curt Class III Trailer Hitch, # C13128, is the same on your 2012 Range Rover Evoque Dynamic as it is on the Pure and Prestige trim packages. Your square exhaust tips will have no affect on the installation.
There will be some minor trimming of the heat shield and fascia required for installation and the exhaust will need to be temporarily lowered. I have attached a link to the installation instructions for you to check out.
If you will be using this hitch to carry hitch mounted accessories such as a bike rack or cargo carrier, then I also recommend picking up the Curt Stabilization Strap, # 18050. Curt requires all non-trailer loads to be supported by a stabilizing strap.
You will also want to pick up a ball mount, # D-4, Hitch Pin and Clip, # PC3, and a hitch ball, # 19260 for 1-7/8 inch ball or # 19247 for a 2 inch ball.
Products Referenced in This Question
Curt Cam Buckle Stabilizing Strap for Hitch-Mounted Accessories - 61" x 1" - Qty 1
- Accessories and Parts
- Hitch Bike Racks
- Hitch Cargo Carrier
- Tie Down Straps
- CURT
more information >
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- CURT
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 600 lbs TW
- 4000 lbs GTW
- 2 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Article: How to Correct Noise from Exhaust Rattling Against a Trailer Hitch
- Q&A: How Does Brake Controller Install 2020 Chevy Equinox with Tow Package
- Q&A: Trailer Hitch for a 2018 Hyundai Elantra GT
- Q&A: Best Trailer Wiring Harness for a 2018 Land Rover Evoque HSE Dynamic
- Q&A: Tire and Wheel Size to Replace 18.5x8.5-8 on Trailer
- Q&A: Replacement Inner Member Assembly for UFP A 60 Surge Brake Coupler
- Q&A: Replacement Arms for Roadmaster EZ5 Base Plate Kit for 2015 Honda Fit
- Q&A: Parts Needed To Install Solera Awning Fabric On Slide-Out
- Article: How to Use a Roof Rack (Like a Boss)
- Article: How to Charge RV Batteries