Powered A-Frame Jack that Plugs into 7-Way for Powering

Question

Question:

hello, does your electric A frame hitch work on a horse trailer? How does the electric hook up? there is no battery in the horse trailer. but it does have magnetic brakes

asked by: Cheryl D

0

Expert Reply:

One easy solution for powering an A-frame jack on a trailer without a battery is a powered jack that draws power by plugging into a 7-way with an active 12 volt circuit like the Buyers Products Electric Jack part # 3370093500.

expert reply by: Jameson C

0

Answer 1

If you are referring to the lowest point then that would be the bottom of the frame bracket and if the horizontal section of this bracket was placed directly up against the bottom of the frame rail then it would stick down around 8" or so.…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The correct wiring harness for your 2024 Kia Telluride SX Prestige X-Line is the Curt #C29ZV. This plugs into the connection points in your rear cargo area and is compatible with your LED lights. The #TK74CR is only designed to work with the LX and S…

view full answer...

Answer 5

Since your 2024 Telluride X-Line is not an LS or S model the correct wiring harness is the Curt #C29ZV. This will plug into the connection points in the rear cargo area and provide you with a 4-way to power your trailer's signal lights. The…

view full answer...

Answer 6

I'm not sure why they include that replacement latch but that is not required for any of the aftermarket hitches or wiring. It is probably something related to the installation of the OEM hitch. The etrailer #e45ZR you referenced is what I would…

view full answer...

Answer 7

I do have a solution for your 2024 Kia Telluride that has the LED taillights that does allow it to have both a 4-way and 7-way plus install a brake controller but it is not with the #TK74CR which does not work for you based on the LED taillights.…

view full answer...

Answer 8

Yeah, it is definitely a bit to sort through, so I think we can help you out with the right 4-way wiring harness for your 2024 Kia Telluride. We'll start with the easy one, which is if you want to hardwire a 4-way, the model of your Telluride…

view full answer...

Answer 9

A direct replacement for your Winntec Model 6020 is the Automatic Changeover RV LP Gas Regulator #37207-30395 as the BTU rating is compatible and they have the same fitting sizes.

view full answer...

Answer 10

We can definitely help set you up with a tow package for your 2024 Kia Telluride. The main components you will need are a hitch, 7-way wiring harness, and a brake controller. You will need a good ball mount too, but it sounds like you have that…

view full answer...

Answer 11

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 12

The Curt trailer wiring harness part #C93FV would be what I recommend for your 2023 Kia Telluride . This installs easily by plugging inline with your taillights and has a reliable converter box.

view full answer...