Available Plunger and Nylon Socket Door Holder

Question

Question:

Im looking for the nylon holdbacks for 1 plungers. I found them on your site but they seem horribly expensive compared to other sites. Do you get 6? Nylon Socket for DH604 and DH605

asked by: Allie C

0

Expert Reply:

The # DH604 and # DH605 come with both the plunger and the nylon socket, which is where the difference between the part you've linked and the parts you're referencing on our site. These are sold as sets of 1. The Replacement Nylon Socket for DH604 and DH605 # DH600S is available if you're just looking for the nylon socket and not the hardware/plunger, which is also sold singularly.

expert reply by: Erik B

0

Answer 1

Since the hole diameter of the Replacement Nylon Socket #DH600S 1/4" I recommend just getting the whole kit to ensure they work together properly. We have part #DH604 which has a 1" long plunger and part #DH605 which has a 2" long…

view full answer...

Answer 2

I went out to the warehouse and measured the Replacement Rubber Socket #DH38S. The outer diameter is approximately 1-5/8 inches (1.62). The inner diameter is approximately 13/16 inches (0.81). And the height is approximately 1-3/8 inches (1.36).

view full answer...

Answer 3

We have a replacement plunger sockets that could potentially work for your horse trailer window. Check out the Nylon Replacement Socket part #DH600S. This part can also be used on windows and measures 7/8 of an inch tall. For a socket door holder and…

view full answer...

Answer 4

The best solution we have would be an all new plastic stem and rubber socket part #DH39R which gives you both the components needed that we know fit together which means once installed you know it will work great.

view full answer...

Answer 5

We carry two different plunger sockets that could potentially work for you. The Nylon Replacement Socket part #DH600S and the Replacement Rubber Socket #DH38S. For the price and knowing that there wouldn't be any compatibility issues you may be…

view full answer...

Answer 6

To match your 1" long plunger you'll want the Plunger and Nylon Socket Door Holder #DH604. Just like with your old door holder these will hold your trailer doors open with ease by mounting one part to the door and the other to the side of…

view full answer...

Answer 7

The mounting hardware needed to mount the Replacement Rubber Socket for DH38R and DH39R #DH38S is 7mm by 16 threads per inch, and would use a 5/16-16" fastener.

view full answer...

Answer 8

The distance between the mounting holes of the #DH605 is 1-1/4 inches and the holes are 3/16 inch in diameter.

view full answer...

Answer 9

The diameter of the plunger that the Replacement Nylon Socket part #DH600S is designed to fit will be around 1/2" give or take 1/8". The plunger must be larger than the opening on the socket in order to hold it in place. That said, in order…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Available Plunger and Nylon Socket Door Holder

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching