Progressive Dynamics Converter PD9130 Not Working With Charge Wizard

Question

Question:

I have a PD1930 converter and a charge wizard. The battery is fully charged. When I plug in the charge wizard does not show anything, no light and does not do anything when the button is pushed. I have replaced the charge wizard with the same results.

asked by: William D

0

Expert Reply:

There are a couple of things to take a look at with the Progressive Dynamics Inteli-Power RV Converter and Battery Charger # PD9130 & Charge Wizard # PD92201. The most likely is either a blown fuse (or fuses) so you will want to start there. Next, check to make sure it is not overloaded with excessive voltage, as that can cause the unit to shut down.

A short circuit on the wiring is another possibility, and while this can be difficult to check, try tracing the wires to see if there are any broken, crimped, or otherwise damaged.

expert reply by: Kyle S

0

click to enlarge

Answer 1

Yes, for a white base version of the #RVPL7CB you'd want the part #RVPL7C.

view full answer...

Answer 2

The first thing I would want to know here is where you tested the voltage at on the Charge Wizard #PD92201 - if you didn't test it directly at the converter box, you'll want to start there. If the voltage at the converter is different than…

view full answer...

Answer 3

We do carry the lens for the Gustafson 12V RV Porch Light #277-000485 you were looking at with part #291-000002. I was able to find a dimensional drawing of the lens for your current light but I do have the measurements for the lens (pictured below).…

view full answer...

Answer 4

The lens you are looking for is part #APL5CB which is the clear lens for the RV Porch and Utility Light #RVPL7CB.

view full answer...

Answer 5

The PD9140A is a converter that has the smart charger setup built into it so the correct pendent would be the part #PD92201.

view full answer...

Answer 6

The controller would need to be hardwired to your C5500 motorhome as it would not have a harness under the dash using our Brake Controller Installation Kit, part #ETBC7. Due to the fact that your motorhome is longer than the usual passenger vehicle,…

view full answer...

Answer 7

To change the battery mode on the Progressive Dynamics 9300 Series RV Converter Charger #PD79RR you'll need to insert the included CLAW tool into the small opening next to the battery type indicator light. Press and hold that button (using the…

view full answer...

Answer 8

To replace your Parallax 7445 converter you can use the Progressive Dynamics 9200 Inteli-Power Converter #PD9245C. This has the same amperage so you can just reuse the wiring running from the converter to the battery bank. The Parallax 7445 should…

view full answer...

Answer 9

Hey Phil, the correct 60 amp converter replacement that is Lithium compatible is the Progressive Dynamics part #PD79RR. This charges at the higher voltage required by lithium batteries.

view full answer...

Answer 10

To convert the WFCO WF-8955PEC to be lithium compatible you'd need the part #PD4655V and you'd be set. This fits in the panel without any modifications.

view full answer...

Answer 11

The difference between the two models that you were researching is that the #PD9160A is designed for use with lead acid batteries and the #PD9160ALV is designed for use with lithium batteries. Choosing the incorrect battery profile can lead to issues…

view full answer...

Answer 12

The Magenetek Series 900 model 950 was a 50 amp converter so a great option to replace it and get a little more amperage would be the 60 amp Progressive Dynamics Inteli-Power RV Converter and Smart Battery Charger #PD9260C. This is a great unit that…

view full answer...

Progressive Dynamics Converter PD9130 Not Working With Charge Wizard

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching