Steering Stabilizer For 2020 Ford F-53 Chassis With V8 Engine

Question

Question:

What stabilizer fits the 2020 F53 chassis with the V8 engine? These F53s are different, V10 vs V8

asked by: John

0

Expert Reply:

I verified directly with Roadmaster the correct steering stabilizer for your motorhome on a 2020 Ford F-53 chassis with the V8 engine is one of the following, depending on the GVWR of your rig:

- GVWR Less Than 22,000 lbs: Roadmaster Exact Center Steering Stabilizer # RM63RR

- GVWR 22,000 lbs & Up: Roadmaster Exact Center Steering Stabilizer # RM82RR

expert reply by: John R

0

Answer 1

There are 2 sets of instructions for the Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets #RM82RR. One for the steering stabilizer and one for the custom brackets. The instructions for the stabilizer is just a page with some information…

view full answer...

Answer 2

The Reflex is the older version of the Exact Center and has been discontinued. It was essentially just a gas strut with a coil spring around it, whereas the Exact Center is two gas struts with a rod between them that fight to keep the tie rod…

view full answer...

Answer 3

For a steering stabilizer that fits your 2022 Tiffin Open Road Allegro 34PA on a Ford F-53 chassis, I verified with the manufacturer the correct fit, which is the following part number: - Roadmaster Reflex Steering Stabilizer #RM82RR You made a…

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

The torque spec for the rear U bolts on your 2019 F53 motorhome are dependent on the size. If you have 3/4 x 16 u bolts (and used a 1 1/8" socket to remove the nuts) then they torque to 250 lb-ft. If the u bolts are 7/8 x 14 (and you used a 1…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

There is a suspension enhancement option for your 2021 Entegra Vision XL built on a Ford F-53 chassis, but I verified with the manufacturer that the steering stabilizer only fits if you have at least a 24,000 lb GVWR. You're not out of luck…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

We do - for your 2023 Ford F-350 you'll want the TorkLift StableLoad Suspension Upgrade w Quick-Disconnect #TL89CR.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Another wire or harness is not needed on the 2023 Honda CR-V for the install of the Curt 4-Way Wiring Harness #C56370, but you do have to add 20 amp fuse to location #17 in the fuse box.

view full answer...

Steering Stabilizer For 2020 Ford F-53 Chassis With V8 Engine

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching