Mounting Brackets for the Solera Slide Out Topper

Question

Question:

Can I get the piece that goes over the screws that hold the mounts on? All it does is cover up the shinny screws, it looks like.

asked by: Tim D

0

Expert Reply:

The Solera Slide Topper Access Kit part # LC795354 includes the "cover" for the main screws. The main screws attach to the small bracket and you camper. The larger portion of it slides over the screws "covering" them then is held in place with two small black set screws keeping the main screws from being seen.

expert reply by: Randy B

0

Answer 1

Yes, the Replacement Awning Extension Rod for Solera Slide-Topper Awning #LC3452072 that you referenced measures 3/4". I actually recently took this same measurement for another customer for the white version part #LC3452071 and I'm…

view full answer...

Answer 2

I recommend replacing the Extension Rod for your slide topper. With your current rod being bent even if you were able to bend it back straight it will more easily bend in the future or could break. We have the following extension rods for the Solera…

view full answer...

Answer 3

The Replacement Mounting Hardware part #LC701665 comes with the Extension Rods, Extension Rod Bracket, Torsion Arm Caps, and various hardware. I am not sure what all you have now but it sounds like you might also need the torsion heads, part #LC87FR…

view full answer...

Answer 4

I see that you are asking about the Replacement Mounting Hardware for Lippert Solera Slide Topper kit #LC701665. You can purchase the Replacement Slide-Out Hex Bar Extension Bracket #LC2724412 and Replacement Awning Extension Rod #LC3452072 that come…

view full answer...

Answer 5

The correct Solera RV Slide-Out Awning for a 12' or 144" slide-out measuring from the outside of each flange is part #LCV000177334 for black and part #LCV000163298 for white.

view full answer...

Answer 6

Replacement Mounting Hardware for Lippert Solera Slide Topper - Black #LC701665 uses #10 - 16 x 3/4” screws to secure the shaft of the extension rod bracket. I've attached a photo to assist.

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

When choosing the slider you want to measure the outside front of box width including the flange. Then you need to select a slider that extends a minimum of 2-1/2 inches beyond each side of the box width. For example, the Black Solera Slider…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

When installing an awning like the Solera Smart Arm 12V Power RV Awning #LC517486, the arms will be secured to the wall framing. When the awning extends there will be quite a bit of leverage, so it is important to mount the awning to an area where…

view full answer...

Answer 11

Hey Morris, you want to measure from the width of the flange that runs around the edge of the slide out to pick out the correct slide topper. Based on the dimension you took the part #LCV000165061 that you referenced is probably correct but you still…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Mounting Brackets for the Solera Slide Out Topper

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching