What is Overall Height of Timbren Rear Suspension Enhancement System # TNRARM

Question

Question:

Hello, what is the over all height of this products? Thanks.

asked by: Bryan K

1

Helpful Expert Reply:

I checked with Timbren and the overall height of the Timbren kit part # TNRARM is 2-3/4 inches.

expert reply by: Jameson C

1

click to enlarge

Answer 1

The picture you have provided looks like the 2014 Nissan Armada 2-wheel drive model that you have does have a bump stop and Timbren does not exclude 2-wheel drive models so you will be able to use Timbren springs #TNRARM. I have linked a help article…

view full answer...

Answer 2

If you are only experiencing sag on your 2012 Nissan Pathfinder when towing your RV/travel trailer, I recommend going with a weight distribution system over any type of suspension enhancement system. The Timbren Heavy-Duty Rear Suspension Enhancement…

view full answer...

Answer 3

You would want to stick with the weight distribution system. Suspension enhancements like the part #TNRARM that you referenced are better suited for heavy cargo in the rear of a vehicle. They aren't ideal for towing a trailer like a WD system…

view full answer...

Answer 4

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

The Air Lift WirelessONE Compressor System #AL25980EZ and Air Lift WirelessONE Compressor System #AL25980 are nearly identical with only some very minor differences in CFM and duty cycle ratings. The #AL25980EZ will also come with an easier mounting…

view full answer...

Answer 11

Hey David, actually what is going to make the biggest improvement in handling and stability for your 2011 Itasca is an upgraded rear sway bar with the part #RM-1139-175. I know that's not what you asked about but for motorhomes where most of the…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

What is Overall Height of Timbren Rear Suspension Enhancement System # TNRARM

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching