HappiJac Swing Out Extension Brackets

Question

Question:

Ive seen this product listed as #182496 on other websites. Is your product the same? Also, does this come as a set or do I need to buy 2? Thanks!

asked by: Jill R

0

Expert Reply:

The part 182496 is listed on our site as part # LC182496. It is the Swing Out Extension Brackets for HappiJac Truck Camper Jack Systems, and it does in fact come in a set of two. I've linked to a video review of these extension brackets for you.

expert reply by: Kef G

0

Answer 1

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 2

The HappiJac Swing-Out Extender Bracket for Dual Wheel Chassis Truck Camper Jacks #HJ54FR (single) or Swing Out Extension Brackets for HappiJac Truck Camper Jack Systems #LC182496 (double) are not compatible with the Atwood electric camper jacks.…

view full answer...

Answer 3

The correct swing-out brackets for a dually are the HappiJac Swing-Out Extender Brackets for Dual Wheel Chassis Truck Camper Jacks #HJ54FR. In terms of size these will give you 3-1/2" to 4-1/2" of extension. You can use these with the…

view full answer...

Answer 4

I contacted the Rep at Happijac to inquire on your question of the HappiJac Swing-Out Extender Bracket for Dual Wheel Chassis Truck Camper Jacks, #HJ54FR. His response was that yes, you can "stack" the extensions. There is however a point…

view full answer...

Answer 5

I recommend using the Swing Out Extension Brackets for HappiJac Truck Camper Jack Systems item #LC182496 and the HappiJac Fixed Extender Bracket for Dual Wheel Chassis Truck Camper Jacks item #HJ54FR. The fixed extenders are only 5" wide apiece.…

view full answer...

Answer 6

The Swing Out Extension brackets part #LC182496 are designed for HappiJac camper jacks and the 2002 Lance 920 does not have the Happijack system unless you have replaced the jacks at one point. If you have replaced the system with the HappiJacks then…

view full answer...

Answer 7

The Swing Out Extension Brackets for HappiJac Truck Camper Jacks part #LC182496 is the way to go as the 382819 HD are no longer produced. From what I've gathered they were the same width but had a stronger build for heavier campers. They are no…

view full answer...

Answer 8

The HappiJac Swing-Out Extender Bracket for Dual Wheel Chassis Truck Camper Jacks, #HJ54FR, is not compatible with the Atwood-Titan. This offers 3-1/2" to 4-1/2" additional inches of clearance for HappiJac truck camper jacks but is only…

view full answer...

Answer 9

The only extender bracket that we have for the Happijac is the HappiJac Extender Bracket for Dual Wheel Chassis Truck Camper Jacks #HJ54FR that you mentioned.

view full answer...

Answer 10

If one set of the HappiJac Extender Brackets part #HJ54FR doesn't provide enough clearance Happijac has told us that you can use a second set to gain additional clearance.

view full answer...

Answer 11

As we do not carry the Atwood jacks, I cannot confirm the fitment without knowing the measurements. However, the bolt holes on the HappiJac Swing Out Extension Brackets #LC182496 will measure 7-1/4" between all the bolt holes, picture included.…

view full answer...

Answer 12

We have a Swing Out Extension #LC182496 as well as an Extender #HJ54FR to help your camper pass the sides of your truck with the dual wheels. The swing out extensions add 3-1/2" to 4-1/2" of length depending on your mounting brackets and…

view full answer...

HappiJac Swing Out Extension Brackets

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching