Sidewinder Pin Box that Can Replace Lippert 0719

Question

Question:

will the reese 61421 fit a lippit 0719 pin box. this will be in a short bed silverado pickup

asked by: Bucky M

0

Expert Reply:

We do have a cushioned version of the Sidewinder pin box with the part # RP61422 which is a fit for the Lippert 0719 that you have but the kit you mentioned is not a fit.

I attached a couple install videos for this for you to check out as well.

expert reply by: Jameson C

0

Answer 1

Although the MORryde Orbital Pin Box and the Reese Revolution perform the same function (moving the pivot point further back for short bed trucks), the Revolution is a plain pin box while the Orbital has a cushioning block of rubber built in to help…

view full answer...

Answer 2

I attached a picture as well as a help article that includes a chart that has all of the pin boxes we offer Sidewinders for.

view full answer...

Answer 3

For a 5th wheel trailer hitch that, when removed, leaves a clean bed in your 2014 Ford F-150 short bed you can use the B and W installation kit #BWGNRK1104-5W with slider Companion 5th wheel trailer hitch #BWRVK3400-5W. The slider provides 12 inches…

view full answer...

Answer 4

Normally there will be a plate or sticker on the pin box of a fifth wheel trailer that will tell you the model name and number. If you cannot find the number you can use the measurements of the bolt holes of the pin box to determine which one you…

view full answer...

Answer 5

The Demco Hijacker Autoslide 5th Wheel Trailer Hitch w/ Slider #DM8550034 can only use a lube plate that is a maximum of 3/16 inches thick so you can use the #RP83004 that is 12 inches diameter and 1/8 inch thick or the Curt 10 Inch #16721 that is…

view full answer...

Answer 6

It sounds to me like the gears of the slider inside of your Replacement Head and Base Assembly for Demco Hijacker Autoslide 5th Wheel Trailer Hitches #DM6077 may either have debris blocking them, the teeth may be chewed up and need to be replaced, or…

view full answer...

Answer 7

When using a slider 5th wheel trailer hitch you should only tow with it in the forward most position and not when slid back. The hitch should only be slid back when making tight maneuvers that require more clearance. If the trailer where slid back…

view full answer...

Answer 8

In order for the MOR/ryde pin box to work with your Demco Hijacker Autoslide 5th Wheel Trailer Hitch part #DM8550034 you need to have the Demco Hijacker Autoslide Locking Plate part #DM6025 installed on the pin box. The lack of this locking plate is…

view full answer...

Answer 9

Thank you for your purchase of Demco Hijacker Autoslide Locking Plate for Standard 5th Airborne Pin Boxes, part #DM6026. The issue you describe sounds like it could be related to the jaws on your Demco Hijacker, if it is an older unit with E or F…

view full answer...

Answer 10

There is not an adapter needed for the Trailair Rota-Flex 5th Wheel Pin Box, like #LC328330, with the Demco Hijacker Autoslide 5th Wheel Trailer Hitch w/ Slider - Single Jaw - Above Bed - 18,000 lbs, #DM8550034, you mentioned. They are compatible and…

view full answer...

Answer 11

If you're having issues coupling to your Demco Hijacker Autoslide 5th Wheel Trailer Hitch w/ Slider - Single Jaw - Above Bed - 18,000lbs the jaws could need to be greased but it could also be the handle or the internal springs. When pulling the…

view full answer...

Answer 12

Yes, the Demco Hijacker Autoslide 5th Wheel Trailer Hitch w/ Slider, like the 18K #DM8550034 for industry standard beds, will work with the Rota-Flex pin boxes when you use the Capture Plates #DM6171.

view full answer...

Sidewinder Pin Box that Can Replace Lippert 0719

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching