Which Wire Clip for Use with 1/4 inch Steel

Question

Question:

I am looking for a frame clip that will work with 1/4 inch thick frame metal. Which size small, medium, large body clip should I order?

asked by: Don P

0

Expert Reply:

For metal that is 1/4 inch thick the Medium Body Chassis Frame Clip part # SWC9041-1 would be what you'd want. This will be a snug enough fit that it will hold well without being too difficult to fit onto the frame.

expert reply by: Jameson C

0

Answer 1

Coupler Repair Kit #CA-5100-RK includes all parts needed to rebuild an etrailer brand or Ram brand 5K-rated 2-inch ball coupler with a trigger latch. It consists of all components other than the housing. If you have one of these models - #CA5100B,…

view full answer...

Answer 2

The Trailer Valet Jack #TV34FR that you referenced has an inner leg that can travel 14 inches. From the mounting bracket down the jack leg would measure 7 inches at minimum and 21 inches at max.

view full answer...

Answer 3

We offer a few different frame clips. The Wire Frame Clip Item #464600 which is 1-1/2" long x 1/2" wide with a 3/8" gap for wiring. We also have the Medium Body Chassis and Frame Clip - Qty 1 Item #SWC9041-1 is 1-11/16" x1/2"…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 6

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 7

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 12

The Replacement Amber Lens for MC32AB Trailer Lights #A32AB is a direct replacement for the SAE A P2 DOT 14 and would be what you'd need.

view full answer...

Which Wire Clip for Use with 1/4 inch Steel

Product Page this Question was Asked From

Continue Researching