Shaft and Mounting Hole Dimensions of Locking T-Handle # 37210985

Question

Question:

What size is the square shaft on this unit and how far apart are the mounting screws to mount it to the door

asked by: Greg S

0

Expert Reply:

The width and height of the square shaft of the latch part # 37210985 is right at 1/4 of an inch and the distance between the mounting holes is 1-5/8 inches apart.

expert reply by: Jameson C

0

Answer 1

Though we do have a polished aluminum option, we currently do not have a black T-Handle that will measure to your specifications. With that said, the Camco Replacement Locking T-Handle #CAM44393 will have the mounting holes spaced 1-1/2" apart…

view full answer...

Answer 2

The JR Products Locking T-Handle #37210885 that you referenced features a 5/16" square shaft. The mounting holes on the bracket are spaced apart by 1-1/2", on center.

view full answer...

Answer 3

Yes, we do have locking t-handles. I recommend the Bauer Products T-Handle Lock for Truck Caps item #BA47VR. This t-handle is 3-1/2" long x 2" wide, the length of shaft is 2", and the distance between mounting holes center to center is…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 9

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 10

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Shaft and Mounting Hole Dimensions of Locking T-Handle # 37210985

Product Page this Question was Asked From

Continue Researching