Correct Slide Out Awning for 154" Slide Out

Question

Question:

My slideout is 149” for the inside box by 34”. The outside by the wondow is 154”. What size slideout awning kit would I need to purchase?

asked by: Katgy D

0

Expert Reply:

In order to find the correct Solera RV Slide-Out Awning you'll need to measure the entire slide out from the edge of each flange. If you measured 154" then you'll need to use the Solera RV Slide-Out Awning part # LCV000168109 for black or part # LCV000163300 for white.

expert reply by: Conner L

0

Answer 1

When determining the correct Slider (Slide-Topper) to install on your trailer, you will want to first measure your box width. This is measured on the outside front of the box, including the flange. I have attached an installation video to assist. If…

view full answer...

Answer 2

The only Weight Distribution (WD) systems that we have listed on our site that you shouldn't back up with incorporate the use of a friction sway control like the Reese #83660. You can backup, but the friction sway control must first be…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

For your 2018 Ram 2500 with the factory puck system the best 5th Wheel Hitch is the B&W OEM Companion. If you have the 8 foot bed then you will want the fixed 25K #BWRVK3600 and if you have the short 6-1/2 foot bed you will need the 20K Slider…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

Sorry Jennifer, I am a bit confused as you were looking at the Replacement U-Clamp Bracket #RM-B141 which mounts with bolts and not U-bolts. This part works with the Split Bushing #RM-205217-10 for the discontinued Roadmaster Front Anti-Sway Bar…

view full answer...

Answer 9

Brien, it sounds like you did your research so kudos to you, but the awning you're looking at is not going to work with the wind sensor. You'd need to use the Solera Smart Arm 12V Power RV Awning #LC517517 instead. You're also going to…

view full answer...

Answer 10

Hi Joe, The Blue Ox Base Plate Kit #BX1139 is a confirmed fit for your 2024 Jeep Wrangler Rubicon X per Blue Ox. I don't currently have an installation video on a model with a steel bumper but I did measure from the mounting holes down to the…

view full answer...

Answer 11

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 12

Hey Jason, I spoke with Furrion and they stated that the Furrion Chill Cube is OEM only currently and should be released to the aftermarket distributors later on this year (2024), but there is no solid date. That says to me that they're probably…

view full answer...