Mounting Boat Trailer Bunk Boards to Vertical Bunk Boards that Tilt
Question:
What hardware do you recommend for mounting a bunk board on its edge to vertical bunk brackets? I need the bunk board to pivot on whatever bolt or shaft is used because this is a tilt trailer application with pivoting bunks. Should I use a regular hex bolt and nut or some kind of pivot shaft with pal nuts on the end?
asked by: Tim
Expert Reply:
I like the idea of using a shaft and pal nuts. That way there is less of a chance of it binding up like what might happen if you used regular nuts and bolts. You would have to make sure the shaft has the capacity for the load that you are going to put on it. A shaft like # CE10727A as an example is a solid steel bar, 5/8 inches in diameter and while it does not have an official capacity it would be very sturdy. I have included a link to the other shafts we carry.
Products Referenced in This Question
Roller Shaft with Pal Nuts for Boat Trailer Rollers - Zinc-Plated Steel - 13" x 5/8"
- Boat Trailer Parts
- Rollers
- Roller Shafts
- 5/8 Inch Diameter
- Zinc-Plated Steel
- 13 Inch Long
- CE Smith
more information >
Product Page this Question was Asked From
CE Smith Light Duty, Vertical Bunk Bracket - Galvanized Steel - 12-5/8" Tall - Qty 1
- Boat Trailer Parts
- Bunks
- Bunk Bracket
- 12-5/8 Inch Tall
- Galvanized Steel
- CE Smith
more information >
Continue Researching
- Shop: 40 Ft 5-Way Trailer Wiring Harness - Wishbone Style - 30" Ground - 5' Auxiliary Wire
- Article: Wiring Trailer Lights with a 5-Way Plug (It's Easier Than You Think)
- Search Results: wishbone harness
- Shop: Kodiak Trailer Hub for 3,500-lb Axles - 5 on 4-1/2 - Galvanized Steel
- Video: Performance Tool Hook Probe Circuit Tester Review
- Article: Brake Controller Installation: Starting from Scratch
- Shop: CE Smith Bolt for Bolster and Swivel Bracket Assemblies - 1/2" Diameter - Zinc - Qty 1
- Shop: CE Smith Knife, Pliers, and Tackle Rack - Polypropylene - White
- Shop: CE Smith Swivel Bracket for Boat Trailers - Galvanized Steel - 2-1/2" Hole Centers - Qty 1
- Shop: CE Smith Locknut for Bolster and Swivel Bracket Assemblies - 1/2" Diameter - Zinc - Qty 1
- Shop: CE Smith Flat Washer - 1/2" Inner Diameter - Zinc
- Q&A: Should Bunk Boards Tilt While Loading the Boat on the Trailer
- Q&A: 10 Foot Long Carpeted Bunk Boards for Boat Trailer
- Search Results: 4 inch bow roller
- Q&A: Dexter Hub Vs. Kodiak Hub Comparison
- Video: Kodiak Trailer Hubs and Drums - Hub - Q-HUB84545 Review
- Q&A: What Circuit Does Center Pin of 7-Way Trailer Wiring Connector Carry
- Q&A: Replacing 4-pin Plug with a 5-Way Plug So I Can Back My Trailer
- Shop: Trailer Hitch
- Video: Choosing the Right Trailer Wiring
- Article: Trailer Wiring Diagrams
- Search Results: 44649
- Q&A: 10k Dexter Replacement Hub for a 8-415
- Q&A: Can Hydraulic Brakes of Demco Tow Dolly be Converted to Electric Brakes
- Video: Choosing the Right Brake Controller
- Search Results: 68149
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: 25580
- Article: How to Choose the Right Trailer Hitch Class