Replacement Thermostat for 2013 Forest River Heritage Glen

Question

Question:

I have a 2013 Forest River heritage Glen wildwood Trailer. When I turn the furnace on, the air conditioner comes on at the same time . Please help!! Do I need to replace the thermostat and where could I get a one ?

asked by: Jeannette

0

Expert Reply:

With your Furnace and Air Conditioner turning on at the same time, there appears to be an issue with the thermostat as you stated. The Replacement Premium Wall Thermostat for Furrion Chill RV Air Conditioner - Single Zone - Black # FR33PR is designed for Furrion AC systems which replace the Dometic Brisk systems. It will allow you to select between furnace and AC.

expert reply by: Jason S

0

Answer 1

The Replacement Single Zone Thermostat for Dometic RV Air Conditioners #DMC79FR is a single zone 3 wire thermostat like the one you are describing. I have attached the wiring diagram for this thermostat and the control box below for your reference.

view full answer...

Answer 2

When wiring the Single Zone Thermostat for Dometic RV Air Conditioners #DMC79FR, the solid red wire goes from the positive terminal of your RV's power supply to the control box of your a/c. The positive power wire from the control box to the…

view full answer...

Answer 3

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 4

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 5

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 8

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 9

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 10

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Replacement Thermostat for 2013 Forest River Heritage Glen

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching