9/16 Inch Lug Nuts and Drive-In Trailer Hub Studs

Question

Question:

I need the hub wheel studs and lugs. I know they are 9/16.

asked by: John A

0

Expert Reply:

For 9/16" lug nuts we have the Trailer Wheel Lug Nut - 9/16" # 6-53.

Then, for drive-in 9/16" wheel studs, which are 2-1/2" long, the correct part is the Trailer Hub Wheel Stud # 7-257.

These are sold individually so you'll want to make sure you order the appropriate amount for your hub and wheels.

expert reply by: Kyle S

0

Answer 1

For the etrailer hub #AKHD-865-8-K you'd need the replacement studs part #7-257.

view full answer...

Answer 2

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 3

The standard torque on a Redline Trailer Wheel Lug Nut - 9/16 inch, part #6-53, is 135 to 145 ft lbs. This is the torque range that is normally used. If the instructions for the wheel are saying 110 ft lbs there might be a reason, like the wheel…

view full answer...

Answer 4

It does sound like the previous owner did not install the assemblies correctly. An easy way to make sure you have the brakes on correctly is to lock at the actuating arm. It should always point towards the front of the trailer. I have included a…

view full answer...

Answer 5

The pulling you are experiencing does indicate that the brakes are applying harder on one side than on the other. You mentioned in your question that you recently repacked the bearings - was this done before the pulling issue began or after? The…

view full answer...

Answer 6

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The correct torque for installing lug nuts on your 5 X 8 trailer's 5-lug wheels will depend on the size of the lugs. For a 1/2-inch lug the torque spec ranges from 75- to 85-ft-lbs. For a 9/16-inch lug the torque spec ranges from 135- to…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

9/16 Inch Lug Nuts and Drive-In Trailer Hub Studs

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching