Correct Over Under Spring Kit for Dutchmen Coleman Lantern 300TQ

Question

Question:

I would like to purchase a kit so I can gain ground clearance. I have a stock 2016 Coleman 300TQ Toy Hauler. Tandem axel. I am 99.9 sure the axels are Dexter.

asked by: Ryan

0

Expert Reply:

In order to confirm fit of the Dexter Trailer Springs Over-Under Conversion Kit you simply need to know the axle capacity or axle diameter. It does not need to be a Dexter axle in order for the kit to work. If you have 2-3/8" diameter axles which are usually 3,500 lbs then use part # K71-384-00 but if they are 3" diameter which are usually between 5,200 lbs and 7,000 lbs then use part # K71-385-00.

The Dutchmen Coleman Lantern 300TQ likely uses 3/8" diameter axles which are 3,500 lbs so part # K71-384-00 should be correct.

expert reply by: Conner L

0

Answer 1

From the axle tag you provided (thank you!), you do indeed have a 4,400 pound Dexter axle. The only hub/drum we carry that is compatible is the Trailer Hub and Drum Assembly - 4,400-lb E-Z Lube Axles - 10" Diameter - 6 on 5-1/2 #8-407-5UC3-EZ.…

view full answer...

Answer 2

We don't carry replacement Lippert axles at this time but we can help with everything else you said you needed. For a 6 lug 4,400 lb trailer hub/drum we have the part #8-407-5UC3-EZ. This comes with bearings, races, and seal. Then for brake…

view full answer...

Answer 3

A 4,400 pound Lippert axle has a 6 on 5/12 bolt pattern and uses bearings #L44649 and #LM67048. So a good replacement hub that includes a bearing kit is part #8-407-5UC3-EZ.

view full answer...

Answer 4

The correct hub and drum assembly replacement for your Lippert 4,400 lb axle is the #8-407-5UC3-EZ. This comes with bearings and a grease seal. If you need brakes as well you can use the #LC66WD, or for self-adjusting brakes #K23-478-479.

view full answer...

Answer 5

Many times Dexter hubs will fit on a Lippert axle, but Lippert does have a few axles out there with special spindle sizes. Every Lippert axle comes with a tag or plate on the axle that gives a serial number or NV number. If you can give me that…

view full answer...

Answer 6

The Trailer Hub and Drum Assembly #8-407-5UC3-EZ is a lug centered hub with a pilot hole size of 3.62". Your 99.25mm(3.75") hub bore wheels will fit on hub/drum.

view full answer...

Answer 7

The Patriot Slider part #BWRVK3270 might be a bit more noisy than the Companion slider part #BWRVK3400 due to the increased number of mounting points, 4 at the corners vs. 1 in the center. Probably not that noticeable and certainly not something…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Correct Over Under Spring Kit for Dutchmen Coleman Lantern 300TQ

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching