Can the Kwikee 26 Series Electric RV 1-Step Be Obtained Without the Motor

Question

Question:

Do you have replacement steps for the Kwikee 3711363? I have the motor and amber light, just need the step assembly.

asked by: Jason J

0

Expert Reply:

The Kwikee 26 Series Electric RV 1-Step is offered with the motor, control unit, and switch as part # LC3711363; the motor and control unit as part # LC371136, and motor and switch as part # LC3711361 but these are the only configurations available.

expert reply by: Conner L

0

Answer 1

I checked with Lippert and the Kwikee 26 Series step does not have an available frame replacement for it, so you will need to replace the entire step assembly. For a new Kwikee 26 Series Step you'll want to use the #LC3711361, which fits on…

view full answer...

Answer 2

Yes, the Voyager RV Backup Camera w/ Night Vision #VGR84VR would be a compatible option for your Jensen VR187 RV Stereo. I found the user manual online with a diagram showing the rear and side marker camera hookups. If the rear camera wiring you have…

view full answer...

Answer 3

In order to add the grid lines to your Voyager RV Backup Camera w/ Night Vision - Rear Mount #VGR84VR you are going to need to get into the menu screen on your monitor like #VO34FR, and through the settings you'll just need to toggle the marker…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 11

It really just depends on what the wires are for. Most likely you have several ground wires among the 8 as well as a couple running light circuits in there as well. You just have to run all of the wires to the correct circuits. The 4-way wiring of…

view full answer...

Answer 12

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Can the Kwikee 26 Series Electric RV 1-Step Be Obtained Without the Motor

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching