Height of the Load Stops for Thule Aeroblade Load Bars, Ladder Racks, or Thule TracRac CapRac

Question

Question:

How tall are they?

asked by: Jim K

0

Expert Reply:

The Replacement Load Stops for Thule Aeroblade Load Bars, Ladder Racks, or Thule TracRac CapRac # 753-3761 will sit 5" above the crossbars. The 5" height does not include that piece that sits inside the T-Slot of the crossbar so it will just be the actual load stop that is the 5" height (see attached).

expert reply by: Jon G

0

click to enlarge

Answer 1

In order to install the Replacement Tie-Down Cleat part #TA01-27046 you are going to want to use a 1/4"-20 x 1-3/4" socket head cap screw. We do not carry this screw separately so you would need to source it from your local hardware…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 7

We have not had the opportunity to do a brake controller installation on a 2023 Nissan Frontier yet. But if the plug is located in the same place as the 2022 model year, then the plug will be tucked behind the kick plate located to the left of the…

view full answer...

Answer 8

From what I could find, it looks like the plug for a trailer brake controller on your 2023 Nissan Frontier is located in the same location as the 2022 model year. That is behind the side panel by the OBD connector and is likely pushed back into the…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Height of the Load Stops for Thule Aeroblade Load Bars, Ladder Racks, or Thule TracRac CapRac

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching