Mounting Bracket Adapter to Draw-Tite Hitch # 75155
Question:
Do you have a mounting bracket to fit this adapter # HM43374 to a Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2 Item # 75155? The holes on the hitch are about 3inch on center and the holes on this adapter are about 2 1/4. Right now I have it mounted with one screw and a zip tie but it doesnt look good nor does it seem like it will hold up long term. Would really love to be able to bolt it down good to the hitch. I specifically bought this hitch for that purpose and right now its not right.
asked by: Tom
Expert Reply:
The Hopkins Plug-In Simple Vehicle Wiring Harness for Factory Tow Package - 7-Way and 4-Flat Connectors # HM43374 will use a standard bracket like the one that came with it. This is a standard fit if you use a bracket like # 18140 or # C57202.
The mounting bracket on your trailer hitch receiver # 75155 is a fit for the factory wiring harness only as you can see in the attached video.
Other options are the # C58000 and # 18159.
Products Referenced in This Question
No-Drill Mount for Electrical Mounting Bracket - Short
- Accessories and Parts
- Trailer Wiring
- Mounting Hardware
- Brackets
- 4 Flat
- 5 Flat
- 4 Round
- 5 Round
- Tow Ready
more information >
6 and 7-Way Trailer Connector Mounting Box for Round or Square Tube Hitches
- Accessories and Parts
- Trailer Wiring
- Mounting Hardware
- Brackets
- 6 Round
- 7 Round
- Draw-Tite
more information >
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class IV
- 600 lbs TW
- 6000 lbs GTW
- 7300 lbs WD GTW
- 2 Inch Hitch
- 730 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Curt No-Drill Bracket for 6-Way or 7-Way Round Trailer Connector Mounting Bracket - Long
- Accessories and Parts
- Trailer Wiring
- Mounting Hardware
- Brackets
- 6 Round
- 7 Round
- CURT
more information >
Curt Easy Mount Bracket for 4- or 5-Way Flat and 6- or 7-Way Trailer Connectors - 2" Hitch
- Accessories and Parts
- Trailer Wiring
- Mounting Hardware
- Brackets
- 4 Flat
- 5 Flat
- 6 Round
- 7 Round
- CURT
more information >
Product Page this Question was Asked From
Hopkins Plug-In Simple Vehicle Wiring Harness for Factory Tow Package - 7-Way and 4-Flat Connectors
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 7 Round - Blade
- 4 Flat
- Hopkins
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Raise Your Travel Trailer Height
- Q&A: Recommended Replacement for Atwood Surge Brake Actuator 85778
- Article: Trailer Wiring Diagrams
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: How Do You Disconnect Factory 7-way Connector On 2007 Toyota 4Runner To Install Hopkins HM43374?
- Q&A: Mounting the Replacement Wiring Harness For Factory 7-Way On a 2008 Toyota 4Runner
- Article: Pintle-Hitches
- Q&A: Trailer Wiring Recommendation for 2007 Toyota 4Runner that Has Two Connectors
- Q&A: Install Instructions Link for Lippert Lift Kit # LC382741
- Q&A: Torque of Mounting Nuts on Lippert Torsion Axle Lift Kit
- Article: Where to Position the Trailer Axle?
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Slipper Spring Trailer Suspension System Review