Can Stromberg Carlson Trailer Jack be At Different Angle on Mounting Bracket

Question

Question:

Can this unit be rotated 90 degrees on the mount to give additional tailgate clearance?

asked by: Brian

0

Expert Reply:

Yes, if you wanted to turn the Stromberg Carlson Electric Trailer Jack # JET-3755 so that the housing was at an angle to give you more tailgate clearance you certainly could.

expert reply by: Jameson C

0

Answer 1

If you've only used the Electric Jack w/ Footplate #EJ-3520-BBX for one camping trip and it is only lowering the trailer now there are 3 possibilities.: 1) - Your battery that you are using to power the jack is depleted and needs to be charged.…

view full answer...

Answer 2

The Stromberg Carlson 4000 Series 5th Wheel Louvered Tailgate with Lock #VGM-99-4000 replaced the Stromberg Carlson 3500 Series Tailgate VGM-99-3500. Stromberg has discontinued the 3500 series tailgate. The 4000 series is a bit lighter than the 3500,…

view full answer...

Answer 3

I reached out to the manufacturer, Stromberg Carlson, who told me their 3,500 lb Electric Trailer Jack #JET-3755 (Black) and #JET-3555 (White) has a travel speed of 10 inches over 55.5 seconds with no load. This is a relatively normal speed for a…

view full answer...

Answer 4

Most jacks, like the Stromberg Carlson #JET-3755, will allow you to open up the tailgate on your truck if you rotate the the trailer jack. Most people mount the trailer jack so that the controls face the direction of travel but there is nothing wrong…

view full answer...

Answer 5

The first thing I recommend is checking the ground connection as this jack is grounded through the mounting plate. Sometimes removing some paint and/or using a star washer is a good option to make sure there is metal to metal contact for proper…

view full answer...

Answer 6

Weight distribution works to distribute the tongue weight of a trailer up to the front axle of the tow vehicle so that it will sit more level and handle/brake better. That being said the systems do not "reduce" tongue weight or allow you to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

The rule of thumb for estimating a tongue weight is 10-15 percent of trailer weight. A 4,600 pound trailer would have a tongue weight between 460 and 690 pounds. Somewhere between a 1,000 to 2,000 pound capacity jack would be fine. Having a jack that…

view full answer...

Answer 12

We do have the panels separately. What you're looking for is the Go Power Overlander Expansion Kit - 200 Watt Solar Panel #34282182.

view full answer...

Can Stromberg Carlson Trailer Jack be At Different Angle on Mounting Bracket

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching