Installation of Redarc Brake Controller on 2017 Jeep Grand Cherokee with Factory 7-Way

Question

Question:

Any chance the connector for a Prodigy brake controller fits into the Redarc controller? I have a 2017 Jeep Grand Cherokee and have made a cable for the Prodigy. Do I have to take that apart and connect a Redarc connector to my Jeep connector? Thanks

asked by: Doug B

0

Expert Reply:

The Redarc Tow-Pro Elite Trailer Brake Controller - 1 to 3 Axles - Proportional # RED44FR does have an adapter harness # RED77FR that will plug directly into the factory connector on the 2017 Jeep Grand Cherokee.

expert reply by: Jason S

0

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you don't have to worry about the water damaging wires like you would with electric brakes. That being said, if you use a heat shrink butt…

view full answer...

Answer 4

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Answer 5

By all accounts the Curt Spectrum Trailer Brake Controller #C51170 works well and is easy to use and install on most vehicles. It is a brand new item so not a lot of feedback has come in on it. I did learn a few things though after speaking with our…

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

Hey Donald, the best Blue Ox weight distribution would be the pat #BXW0550 as it has a perfect tongue weight range for your 450 lb tongue weight trailer.

view full answer...

Answer 8

I attached a picture that shows how much of the etrailer.com hitch part #E98901 would hang below the rear bumper when installed.

view full answer...

Answer 9

The Hopkins tow bar wiring harness #HM59VR that you referenced is the same as the Hopkins part number 56209 and is for sure a confirmed fit for your 2018 Jeep Grand Cherokee. We sometimes have to change part numbers because more than one manufacturer…

view full answer...

Answer 10

I recommend the Redarc Tow-Pro Liberty Brake Controller #RED24FR for your 2023 Toyota Tacoma with the factory tow package. You will be able to connect the wiring using the Redarc Adapter #RED99FR directly to the factory connector. We also have the…

view full answer...

Answer 11

For your 2024 Nissan Frontier I recommend the Redarc Tow-Pro Liberty Brake Controller #RED24FR. I like the Liberty because it is simple, reliable, and looks great in any vehicle. The main unit installs behind the dash, so only the control knob will…

view full answer...

Answer 12

Yes, when installing the knob for the Redarc Tow-Pro Liberty Brake Controller item #RED24FR you will want to remove any extra material behind the insert. I am happy the video was able to help you out. I have linked a couple of pictures from the video…

view full answer...

Installation of Redarc Brake Controller on 2017 Jeep Grand Cherokee with Factory 7-Way

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching