What is Bolt Pattern of 4 Bolt 3,500 lb Trailer Brake Assembly # AKEBRK-35-SA

Question

Question:

Can the 4 mounting bolts pressed in be easily removed? I need longer studs for my application. What is the mounting hole/bolt spacing?

asked by: Jim

0

Expert Reply:

I wouldn't say the studs of the brake assembly # AKEBRK-35-SA are easily removable but it would be possible since they are pressed in. It would be like removing any standard wheel stud from a hub. I attached a picture that shows the bolt pattern as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Electric Trailer Brake Kit #AKEBRK-35-SA comes with both the right and left brake assemblies but also new nuts and washers. If you get the brakes individually the nuts and washers are sold separately. If you do not need the nuts and washers then…

view full answer...

Answer 2

Were you moving when you hit the manual override lever of your brake controller? The trailer wheels have to be moving forward for the adjustment to happen with every application of the brakes. You might also make sure the brakes weren't installed…

view full answer...

Answer 3

The biggest difference between Dexter brake assembly #23-459 and etrailer/AxleTek assembly #AKEBRK-7L-SA is the pad material. The Dexter assemblies use pads that are snapped off of a long strand of the material. The ones on the etrailer assemblies…

view full answer...

Answer 4

The Electric Trailer Brake Kit part #AKEBRK-35-SA is designed for 3,500 lb axles and has a self-adjusting feature so there will be no need to continually adjust the assemblies for wear after the initial adjustment. Fortunately, axle capacity is the…

view full answer...

Answer 5

In regards to electric trailer brake assemblies like the Electric Trailer Brake Kit part #AKEBRK-35-SA, these are side specific meaning there is both a left/driver and right/passenger side. If you're unsure of which side is which, just look at…

view full answer...

Answer 6

I would measure the distance between the center of one bolt hole to the center of the bolt hole adjacent to it, and not the diameter. If the distance is: 2-5/8" - the bolt pattern is 5 on 4-1/2 2-3/4" - the bolt pattern is 5 on 4-3/4…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 10

Thanks for the photos and information. You will want the Electric Trailer Brake Kit - Self-Adjusting - 10" - Left and Right Hand Assemblies - 3,500 lbs #AKEBRK-35-SA for self adjusting brakes that you won't need to check periodically to…

view full answer...

Answer 11

Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you don't have to worry about the water damaging wires like you would with electric brakes. That being said, if you use a heat shrink butt…

view full answer...

Answer 12

You will need to do some measuring to determine if the 10 Inch Electric Brake Assembly LH, item #AKEBRK-35L, is the correct assembly for your trailer. Measure the diameter of the mounted brake shoe, the width of the lining and the distance between…

view full answer...

What is Bolt Pattern of 4 Bolt 3,500 lb Trailer Brake Assembly # AKEBRK-35-SA

Product Page this Question was Asked From

Continue Researching