Replacement Side Frame Mount Jack for Pop-Up Camper

Question

Question:

Do you have a recommendation for a replacement jack on our 1999 Viking pop up M-2465. The current jack is a side mount, top wind, Alko 8 in wheel with # 244304123973?

asked by: Craig

0

Expert Reply:

That's an interesting jack, and there are no specific replacements for it so what you are going to need to do is have your mounting bracket removed and new one welded on.

For this I recommend the Jack Mounting Bracket # P9012-00 with Fulton Marine Jack # FXP100W0301.

It says "marine jack" but that just refers to its coating to reduce corrosion so it will work on your pop-up trailer.

expert reply by: Kyle S

0

click to enlarge

Answer 1

The best option jack we have that has a 2 inch outer diameter is the A-Frame Trailer Jack - Sidewind - 1,000 lbs. by Dutton-Lainson #DL22530 which can use the landing foot #DL22541 or the caster #DL22414. This obviously has the A-frame mount…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 4

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

I recommend using the Roadmaster wiring for your 2024 Ford Maverick because I've found it to be the most reliable on the market. The correct kit depends on if your Maverick has LED lights or not: - LED Lights #RM38FR - Non-LED Lights #RM-15267…

view full answer...

Answer 12

I have good news, our trailer jack that has a 2 inch outer diameter part #DL74MR would fit and work well. While it has a 1,000 lb weight capacity that does not mean 1,000 lb total trailer weight capacity. That capacity is the tongue weight capacity…

view full answer...