Installing Tekonsha Prodigy RF on 2001 Fleetwood Bounder Motorhome
Question:
how to wire 7 plug for 2001 fleetwood bounder for # 90250 controler
asked by: David
Expert Reply:
You would begin by installing a 7-way connector at the rear of the coach. How this is done will depend on whether you already have a functional 4-pole connector. If you do, you can simply use an adapter like part # 37185. The adapter would plug into your existing 4-pole, with the white wire grounded to the frame and the black wire extended with a length of 10 gauge wire like part # 10-1-1 and ran to the positive battery terminal via a 40 amp inline circuit breaker like part # 9510. The blue output wire on the adapter would not be needed.
If you do not have a 4 pole, you will need to determine which wiring system your coach uses. I have linked you to an FAQ article that will help you determine which system your coach uses. If it is a 2 wire system with the same tail light bulbs lighting up with the turn signal and brakes, you can install a 4-pole plug # 18002 and directly tap the wires into their proper circuits (white wire ground, yellow wire left turn/brake, green wire right turn/brake and brown wire running lights). If your coach has a 3-wire system with separate amber bulbs or lenses for the turn signals, you will need to install a tail light converter like part # 1191758 which would plug into the 4-pole on the adapter.
Once the 7-way was installed and functional, you would then install the controller. Be sure to follow the pairing instructions listed in the manual to the letter.
I have linked you to the instructions for the Prodigy RF brake controller as well as to the instructions for the tail light converter.
Products Referenced in This Question
4-Way Flat Trailer Connector w/ 60" Harness and Wire Taps
- Trailer Wiring
- Trailer Connectors
- Vehicle End Connector
- 0 - 5 Feet Long
- Plug and Lead
- 4 Flat
- Tekonsha
more information >
Adapter 4-Pole to 7-Pole and 4-Pole
- Trailer Wiring
- Wiring Adapters
- Multi-Function Adapter
- 4 Flat
- Plug and Lead
- 4 Flat
- 7 Round - Blade
- Hopkins
more information >
40 Amp In-Line Circuit Breaker - Perpendicular Mount Bracket
- Accessories and Parts
- Wiring
- Circuit Breaker
- 40 Amp
- Pollak
more information >
Product Page this Question was Asked From
Upgraded Circuit Protected Tail Light Converter with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- 1-1/2 Feet Long
- Universal Fit
- 4 Flat
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Semi Trailer Light Function Locations on Heavy Duty 7-Way Pin Connection
- Q&A: Latch Repair Kit For Bulldog A256 2-5/16" Ball Latch Coupler
- Q&A: Replacement Bearings for Dexter 8-222 Hub
- Q&A: Installation of Coupler Repair Kit # CP02-050
- Article: Brake Controller Installation: Starting from Scratch
- Q&A: Solution for Freightliner to Tow Trailer with 7-Way Blade Connector
- Q&A: Dexter D120 Axle Replacement Parts
- Article: Testing Trailer Brake Magnets for Proper Function
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Dimensions for Attachment of the Pro Series Square Drop Leg Jack 12,000 Lbs. # PS1400950376
- Article: Trailer Wiring Diagrams
- Article: Ram Trailer Tow Prep Package
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Diode Installation Instructions for a Dinghy with Separate Tail Light Wiring