Replacement Trailer jack for Ludo Dump Trailer

Question

Question:

I have a weld on top turn trailer Jack on my Ludo dump trailer. It started getting really hard to turn going up and the handle broke off. I raised the to undue up and took out the inside of the Jack. Its a square tube with a threaded rod inside. The tube measures 2 1/4inch square. The threaded rod has a stop inside the tube and wont come out. Is there a repair tube for my trailer itch out having to buy and weld on a new Jack? Thanks

asked by: Rick

0

Expert Reply:

We don't have a repair kit for that jack. Since it sounds like the screw is damaged and the handle is already broke it's time for a new jack. The etrailer jack part # MJSQ-2500B would be a great replacement for this.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Ark Drop Down Corner RV Stabilizer Jacks #ARK94FR are able to lock into place at 30 and 60 degrees as stabilizers. They also have the 90 degree position where it is rated for 1,929 lbs and then the stored position.

view full answer...

Answer 2

Sounds like you are looking for a lower profile jack for your trailer so that the tailgate of the vehicle does not interfere with it. I went to our warehouse and was able to locate an a-frame jack that measured less than 12 inches from the bracket…

view full answer...

Answer 3

I do have an option for you but I don't have any way to reduce the ground clearance of your existing a-frame jack . That said, what you can do to fix this issue is replace your existing jack with the Ultimate Trailer Jack part #322-RDJ-2K.…

view full answer...

Answer 4

I can certainly understand not wanting to have to connect 2 five-foot carpeted bunk rails like #CE27820 to get the 10 foot bunks you need. We don't offer them in the 10' length because the shipping costs would be more expensive than the bunks…

view full answer...

Answer 5

I reviewed some choices which would meet your individual needs and were all non-electric, drop leg, and excellent ground clearance. There were a number of similar jacks, but only one that would mount to your 6” trailer frame. I ordered one from the…

view full answer...

Answer 6

Thank you for the image. It appears you will need either the Demco Channel Tongue Trailer Coupler #DM13203-95 or #DM16080-95. Both of these couplers have a zinc coating for increased corrosion resistance and fit on a standard 3" wide channel…

view full answer...

Answer 7

Yes, you can use 2 of the Timbren Axle-Less Trailer Suspension Kits #ASR35HDS02 which will give you a total trailer GVWR of 7,000lbs. Do understand you must include the weight of the trailer into this calculation. If you are needing to carry 7,000lbs…

view full answer...

Answer 8

You certainly can install two pairs of the Ark Drop Down Corner RV Stabilizer Jacks #ARK77FR on your trailer. In that case we recommend adding one jack to each corner of the trailer frame. Keep in mind that these are designed to stabilize, not lift…

view full answer...

Answer 9

The Dutton-Lainson Square Swivel Jack #DL22340 has a mounting plate designed to fit trailer frames with a height of 3" - 5". I have attached a dimensional drawing below with all of the bolt spacing for your reference.

view full answer...

Answer 10

The mounting holes on Square Jack w/ Footplate - Drop Leg - Bolt On - Zinc - Sidewind - 15-3/8" Travel - 2.5K Item #MJSQ-2500B are spaced 1" apart on center for the top 3 holes and bottom 3 holes. The 2 inner-most holes are spaced…

view full answer...

Replacement Trailer jack for Ludo Dump Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching