Black Garnish for the MaxxFan Deluxe Roof Vent

Question

Question:

Is this compatible with the MaxxFan Deluxe Roof Vent MA00-06200K?

asked by: Luke

0

Expert Reply:

Yes, the Ceiling Garnish for MaxxAir Maxxfan RV Roof Vents part # MA10-20209 will work with the MaxxFan Deluxe Roof Vent part # MA00-06200K. I confirmed this with MaxxAir.

expert reply by: Conner L

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

So long as you are okay with splicing, then Voyager has told us that you can replace your AOM7694 with the Voyager RV Backup Camera Monitor - 7" Screen - 4 Video Inputs #VOM719WP. The wires on the #VOM719WP are labeled, so I recommend making a…

view full answer...

Answer 6

We do offer a hitch that will fit the 2023 Toyota Highlander XLE. Basically any hitch listed under "excluding XSE" is going to fit the XLE model. For you I recommend the EcoHitch Class 3 Trailer Hitch #EH35VR. The main reason I prefer this…

view full answer...

Answer 7

The model number for your MaxxAir vent like the MaxxAir MaxxFan Mini Roof Vent w/ 12V Fan #MA00-04401M, can be found on a sticker stamped on the upper side, if you can't find it there you can also find it located on the bottom and visible when…

view full answer...

Answer 8

The door latches for your Furrion RV Refrigerator - 4 Door - Stainless Steel - 14 Cu Ft #FCR14ACBQASS are part #7 in the diagram below and can be activated by simply pushing the doors in until you hear a click noise.

view full answer...

Answer 9

According to Airexcel, the manufacturer of MaxxFan, their #MA49FR replacement roof flange assembly is compatible with their #MA00-07500K 7500K MaxxFan deluxe fan. I've provided a drawing showing the dimensions of the flange as well as a link to…

view full answer...

Answer 10

We do have the ceiling garnish you are looking for that fits your MaxxFan Deluxe Roof Vent #MA00-06200K. What you need is the part you mentioned, the Ceiling Garnish for MaxxAir Maxxfan RV Roof Vent - White #MA54FR. We assign our own part numbers,…

view full answer...

Answer 11

To install a roof vent lid like the Replacement Lid for MaxxAir MaxxFan Deluxe #MA05-30510 for the MaxxFan Deluxe Roof Vent w/ 12V Fan #MA00-05301K, isn't considered to be a difficult task at all. The unit does not have to be removed from the…

view full answer...

Answer 12

The over under kit part #K71-384-00 that you referenced is for a single axle so if you had a tandem axle setup you'd need to order a quantity of two.

view full answer...

Black Garnish for the MaxxFan Deluxe Roof Vent

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching