Are Replacement Brake Pads BP04-260 the Same as Dexter Axle K71-165-00

Question

Question:

BP04-260 is this a replacement/generic for Dexter axle P/N K71-165-00 or Dexter brand?

asked by: Kathy S

0

Expert Reply:

Yes, the Replacement Brake Pads for Dexter 12-1/4" Duo-Servo Hydraulic Brake Assembly - Left Hand # BP04-260 is just our part number for the K71-165-00 that you mentioned. It's the exact same thing.

expert reply by: Jon G

0

Answer 1

The brake assembly you referenced, Dexter 12-1/4 x 4-Inch Left-Hand Electric Brake #23-438, is indeed rated for 10K axles. This brake matches up to Right-Hand brake #23-439. You can check for fit on your existing axle's brake flanges by checking…

view full answer...

Answer 2

For Dexter 12k oil bath hubs we have the seal part #10-56 which would be exactly what you are looking for.

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 5

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 10

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Are Replacement Brake Pads BP04-260 the Same as Dexter Axle K71-165-00

Product Page this Question was Asked From

Continue Researching