Center Plug for Oil Bath Hubs Availability

Question

Question:

do I have to buy the cap and o-ring just to get the fill plug on dexter axles

asked by: Rocky S

0

Expert Reply:

The plug that is included with the Oil Cap, Plug and O-Ring for Dexter 7-9K Trailer Axles part # RG04-230, 9,000-lb to 15,000-lb Dexter Axle part # RG04-270 and the 9,000-lb and 10,000-lb Dexter Axle part # RG04-300 is not available individually through our sources.

I have linked the options available for you to check out.

expert reply by: Randy B

0

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

With the weight of your camper I recommend the Air Lift LoadLifter 5000 Ultimate Air Helper Springs #AL35FJ. I prefer these as they have the internal jounce bumper which helps to reduce the bounce that is often associated with towing a trailer and…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 8

The best air bag kit for your 2022 Ford F-350 that has a single rear wheel axle is the part #F95FV which has the 5,000 lb capacity you are wanting. Firestone bags are superior Air Lift bags. The ply rating of the rubber is higher, the attachment to…

view full answer...

Answer 9

Yes, you can replace your current Lippert Equa-Flex equalizers with the MORryde AllTrek 4000 Equalizers #MR29DR on your 2018 Highland Open Range. The yellow octagons on the front and rear are a for correcting the alignment of the axles and are not…

view full answer...

Answer 10

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

The Thule TracRac CapRac Ladder Rack for Camper Shell/Truck Cap #TH29200XT is not actually meant to be installed into top tracks. This crossbar system is actually meant to be installed in fixed points on your camper shell so it's not going to…

view full answer...

Center Plug for Oil Bath Hubs Availability

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching