Availability of 16 Inch Channel Mounting Bracket

Question

Question:

I see you list a 12 inch channel on you website. Do you have a 16 inch channel available as well?

asked by: Bradley S

0

Expert Reply:

The 12 inch Adjustable Channel Bracket you'd looked at, part # CTA-CB126 is the tallest channel bracket we offer. The bracket is rated at 15K, there's also a 24K rated bracket of the same height rated at 24K, part
# BDAC5000300.

expert reply by: Mike L

0

Answer 1

The rule of thumb for estimating a tongue weight is 10-15 percent of trailer weight. So your 14,000 pound trailer would have a tongue weight between 1400 lbs and 2100 lbs so any trailer jack rated over 2,500 lbs would be sufficient to lift the…

view full answer...

Answer 2

You will need to check the bolt hole mounting pattern of your Badlands Winch, but we do offer several hitch mounted winch mounting plates that may work. First we have the Curt Mounting Plate, #C31010. On it, the first set of mounting holes are 10 by…

view full answer...

Answer 3

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 6

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 9

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 10

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Availability of 16 Inch Channel Mounting Bracket

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching