Are Replacement Yakima Aero Mount Bales Compatible with the Yakima FrontLoader Bike Rack

Question

Question:

Is the #Y8860053 2 pair an exact match for the #Y8880192.

asked by: Etroy G

0

Expert Reply:

Yes, the Replacement Yakima Aero Mount Bales # Y8860053 are the same as the bale that comes with the Replacement Hardware and Clamp for Yakima FrontLoader # Y8880192. Just be mindful that those bails don't come with the T-Bolt or the knob so if you're missing those then you want the 192 kit.

expert reply by: Jon G

0

Answer 1

For the lower bail piece of the Forklift #Y02098 you would want the part #Y8860053. If you wanted the entire mounting clamp you would want the part #8880208

view full answer...

Answer 2

Most of the Yakima MightyMounts have been discontinued. The best option is the universal set of MightyMounts #Y03590, which work with most Yakima roof bike racks.

view full answer...

Answer 3

Yes, you will remove the brass nut and bolt and the red knob will come off. You should note that the #8880226 does not come with a new nut (just a washer), so be sure not to lose your current one.

view full answer...

Answer 4

If you're wanting to replace the read bar clamp on your Yakima FrontLoader #Y02103, then this is the complete Rear Clamp Assembly #8880208 but if you think the hardware and clamp #Y8880192 is all you need to replace, we have that as well.

view full answer...

Answer 5

According to the folks at Yakima, the front clamp is integrated into the rack and isn't removable, with the exception of the front tensioning handle, which is available as part #8880190. The rear clamp assembly is available as part #8880208. The…

view full answer...

Answer 6

For the bolt that is used to close the Replacement Front Jaw #Y8880189 for the Yakima ForkLift Bike Rack #Y02098 you need the Front and Rear Adjusting Handles #8880139 and Replacement T-Bolts #8860061. The bolts themselves are the same size; it's…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...