Which Solera Awning For Box Width of 150-1/2 inches

Question

Question:

We have a slide that is 150 1/2” long from end to end of the outer wall, what length slide-awning should we purchase, the 12’ 7” model? It would need to be black to match the main awning.

asked by: Bob

1

Helpful Expert Reply:

Yes you would want the 12 foot 7 inch version # LCV000168109 based on the box width you have of 150-1/2 inches.

expert reply by: Jameson C

1

Answer 1

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the…

view full answer...

Answer 2

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 3

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area…

view full answer...

Answer 4

For a standard replacement equalizer for your Dexter 13-122 equalizers you'd want the #TREQE1 or for a cushioned version you'd want the part #K71-653-00 which comes with new shackles and bolts. For a kit that includes new bolts,…

view full answer...

Answer 5

M12-1.5 and 1/2"-20 threads are not going to be interchangeable. The diameter of an M12 thread is only going to be 0.4724" while 1/2" threads are going to be 0.500" in diameter. We currently only have…

view full answer...

Answer 6

I've actually answered a similar question on this before and found: In my research I found that the grease seal you are looking for could have an inner diameter of either 2.24 or 2.12 inches and an outer diameter of 3.37 inches when measured with…

view full answer...

Answer 7

The correct replacement for the Oil Seal 225255UC is the Oil Seal part #9103309. These both have a 2.24/2.25" inner diameter and 3.37" outer diameter. They are also designed for use with oil bath hubs.

view full answer...

Answer 8

If your rear indicators are not working, it's almost certainly a poor ground, so the first thing to do is take a look at your ground connections to make sure they are attached to bare metal surfaces and free of any paint, dirt or corrosion. What…

view full answer...

Answer 9

When choosing the slider you want to measure the outside front of box width including the flange. Then you need to select a slider that extends a minimum of 2-1/2 inches beyond each side of the box width. For example, the Black Solera Slider…

view full answer...

Answer 10

A TruRyde rvd-h-865 7k hub/drum like # AKHD-865-7-2-K uses 1/2-inch drive-in studs that are 1-5/16-inches long. For a replacement stud you can use #165981. This is slightly longer at 1-1/2-inches but it has the same 1/2-inch diameter. They are also…

view full answer...

Answer 11

My research indicates that grease seal part 125255UC has an outer diameter of 1.980-inches and this correlates with the hubs that use bearing #L44649. The seal part most often used with inner/outer bearing L44649 is seal part #10-9 which has an inner…

view full answer...

Which Solera Awning For Box Width of 150-1/2 inches

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching