Recommended 8 Inch Drop Ball Mount WIth Over 12 Inch Length

Question

Question:

Im looking for something specific that I cant seem to find. Im looking for a 8 ball mount, but I would like a minimum of 12 length, 14-16 would be preferred. My GTW is 7500lbs. Shank can be 2 or 2.5. How can I achieve this setup?

asked by: Shea

0

Expert Reply:

It sounds like you are looking for a long and low ball mount. BulletProof Hitches Adjustable 2-Ball Mount for 2-1/2" Hitch - 8" Drop/Rise # HD258 is my recommendation for you. From the center of the hitch pin hole to the center of the ball is 13 inches.

expert reply by: Jason S

0

Answer 1

To add a hitch with a 2-1/2" receiver to your 2018 Ford F-250, I recommend the Curt Trailer Hitch item #C15802. This hitch is custom fit and has a massive 20,000 lbs towing capacity and a 2,700 lbs maximum tongue weight. It can be used with a…

view full answer...

Answer 2

I reached out to B&W, who was able to give me the overall height and width of the B&W Tow & Stow 3-Ball Mount #BW54FR. They told me that overall, this ball mount measured 13-3/4 inches tall and 14 inches wide with the hitch balls in the…

view full answer...

Answer 3

We have an adjustable ball mount for you. First, though, the BulletProof Adjustable Ball Mount that you referenced, part #HD258, has only an 8" drop. Unfortunately, that is not enough for your lowest trailer. The top of your receiver to the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...