Is Chip/Programmer Needed to Install MagnaFlow Exhaust on 2019 Ford F-350 Diesel

Question

Question:

Can I use this exhaust without chipping my truck?

asked by: Trent

1

Helpful Expert Reply:

Yes, you can install the Magnaflow Black DPF Series exhaust part # MF17067 on your 2019 Ford F-350 diesel without having to install a programmer/chip.

expert reply by: Jameson C

1

Answer 1

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 2

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to…

view full answer...

Answer 3

A 16 inch tire will not fit on a 16.5 inch wheel. You would either need to get new 16 inch wheels with the proper bolt pattern to match what the hubs require or to get your existing wheels you would need to go with 16.5 inch tires. You mentioned you…

view full answer...

Answer 4

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 5

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 6

Yes, the Solera Slide Topper part #LCV000168106 is the correct fit for your flange width of 90-1/2 inches. This specific model has a box width range of 86 to 91-3/4 inches which is perfect for your width listed.

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

I do have an option for you, but we do not carry the Dexter 072-027-00 you mentioned. However we do have the etrailer Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR which will be 3/8" shorter but that is still close…

view full answer...

Answer 9

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 10

I spoke to my contact at Horizon Global. He said it is acceptable to mount the Bulldog Powered-Drive Kit #BD1824200100 to the slave jack itself. He also said that if you need to switch the motor wires to make it work correctly, that would be fine, as…

view full answer...

Answer 11

The temperature light on your Everchill RV Refrigerator w/ Freezer #324-000119 is likely flashing because of a lack of full power to the fridge. The fridge requires 11 amps. It is likely trying to use more power than what is available which is why…

view full answer...

Answer 12

According to my research, your 92865A-1 hub/drum has a 25580 inner and an 14125A outer bearing and a 8 on 6-1/2 inch lug pattern, as does the AxleTek #AKHD-865-7-2-K hub drum you referenced. The #AKHD-865-7-2-K would be an acceptable replacement for…

view full answer...

Is Chip/Programmer Needed to Install MagnaFlow Exhaust on 2019 Ford F-350 Diesel

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching