How To Confirm Fit of the Quad TorkLift GlowStep Revolution Scissor Steps

Question

Question:

Hi My question is will the Torklift gloestep revolution with landing gear 4 step, replace my old original fold down 3 step. or is there another model that will slide into mounting bracket left after removal of old steps. Thanks

asked by: Mike

0

Expert Reply:

There are currently two different models of the TorkLift GlowStep Revolution Scissor Steps, part # TLA8104 which is designed for a 25-1/2" mounting bracket and part # TLA8004 for a 27-1/2" mounting bracket. In addition to the mounting bracket width, you also need to verify the entry height is between 32-1/2" - 44". These options are both designed to mount under the door on a trailer which should then have a set of mounting brackets.

I wouldn't have any specifics on your exact steps without further detail.

expert reply by: Conner L

0

Answer 1

Steps like the TorkLift GlowStep Revolution Scissor Steps w/ Landing Gear #TLA8104 are not fit guided for year, make and model of trailer the way a trailer hitch is for a passenger vehicle, which means you will need to take a couple simple…

view full answer...

Answer 2

It appears that your u-bolt plate on your 2021 Grand Design Reflection 31MB, will work with the SumoSprings Trailer Helper Springs #SS26MV. The plate itself including the bends does not appear to be larger than 3/4" nor does the width appear…

view full answer...

Answer 3

Hi Jeremy; that's a good question and you'll actually need to go ahead and re-do the set up of your weight distribution system after adding the Timbren Rear Suspension Enhancement System #TDR1500DS to your 2019 Ram 1500. So it wouldn't…

view full answer...

Answer 4

For your 2022 Grand Design 22RBE with dual 3,500 lb overslung dexter axles the correct SumoSpring kit is part #TSS-107-40. Since your trailer is a tandem axle you will need two of these kits. These are made specifically for overslung axles rated…

view full answer...

Answer 5

I spoke with the manufacturer to ensure the measurements were correct and found that the chart on the page for #LC432690 is incorrect. It does require 27-1/2" of space for the mounting brackets. Both the #LC432690 and #LC432696 will be too big…

view full answer...

Answer 6

Essentially it's how the two scissor steps store. The part #TLA7844 stores more like a traditional scissor step seen typically at the back of truck bed campers while the #TLA8004 stores more like what is seen on the side of campers. Since you…

view full answer...

Answer 7

Since the Torklift Glowstep #TLA7804-8000 has an entry height range of 31 to 42 inches your height of 37 inches would work well.

view full answer...

Answer 8

The TorkLift Glow-Step scissor step assemblies #TLA7804-8000 and #TLA8103 are primarily intended for RV use but there will certainly be other applications where they will work just fine. The key is making sure you will not lose essential ground…

view full answer...

Answer 9

Good news, I can help you find a wider step than the 24 inch LC341504. I've linked all the steps for you but if you look through the filters there should be a measurement column and there are sizes from 14 inches to 30 inches wide. The Lippert…

view full answer...

Answer 10

Installing the Union Tee #AL21838 with your #AL57575 will tie the pressure of the two air bags together. So yes, a shift in a very heavy load like a truck camper will potentially result in air being forced from one into the other. The reason I say…

view full answer...

Answer 11

Traditionally trailer tires have been rated for a maximum speed of 65 mph. You wouldn't find a speed rating on the tire's sidewall and the 65 max was then assumed. Not too long ago tire manufacturers started testing their tires for faster…

view full answer...

How To Confirm Fit of the Quad TorkLift GlowStep Revolution Scissor Steps

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching