Safety Chain Loops for In-Bed Pucks on Ford Trucks

Question

Question:

I understand BandW makes the fifth wheel system for Ford trucks. Is it possible to buy only one safety chain casting? Thanks

asked by: Jerry K

0

Expert Reply:

B&W doesn't offer the safety chain loops for a Ford truck as a separate item, but Curt offers them as part # C60691 which provides two loops that mount into the in-bed pucks. You can see a product demonstration video by clicking the provided link.

expert reply by: Mike L

0

Answer 1

Yes, the ball and safety chain loops of the B&W Ball and Safety Chain Kit for Ford, GM, and Nissan Titan Underbed Gooseneck Trailer Hitch #BWGNXA2061 that you referenced are compatible with the the Andersen Ultimate adapters.

view full answer...

Answer 2

Yes, we have a taller gooseneck ball that fits the OEM rail kit of your 2020 Ford F-350 with the B and W ball part #BWGNXA2061 which measures 5-3/4 inches above the truck bed to the top. See attached picture and review video. This is the tallest…

view full answer...

Answer 3

The best gooseneck hitch ball kit for your 2019 Ford F-350 Super Duty with the factory gooseneck is the B&W Ball and Safety Chain Kit #BWGNXA2061 because its hitch ball is simple to put in or remove and B&W is known for making the most…

view full answer...

Answer 4

Since you have a Lippert 7k axle the correct bearing kit is the part #BK3-210 that you referenced.

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

There's not many differences between the Air Lift WirelessONE item #AL25980EZ and item #AL25980. The main difference is that the item #AL25980EZ has a slightly higher CFM at 1.03 compared to 0.92 and it runs slightly more efficient at 9% over 15%…

view full answer...

Answer 10

The Air Lift WirelessONE Compressor System #AL25980EZ and Air Lift WirelessONE Compressor System #AL25980 are nearly identical with only some very minor differences in CFM and duty cycle ratings. The #AL25980EZ will also come with an easier mounting…

view full answer...

Answer 11

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Safety Chain Loops for In-Bed Pucks on Ford Trucks

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching