Can UWS Truck Bed Toolbox Open on 2016 GMC Sierra 2500 With Tonneau Cover

Question

Question:

will this tool box allow the lid to open up under a tuxedo roll up bed cover

asked by: Dave

0

Expert Reply:

A truck toolbox such as the UWS Truck Bed Toolbox - 5th Wheel Series Chest # UWS01066 will allow the lid to open somewhat, but not entirely if you have a tonneau cover like the TruXedo Pro X15 Soft Tonneau Cover - Roll Up # TX1472001 on your 2016 GMC Sierra 2500.

expert reply by: Kyle S

0

Answer 1

To get the clearance you need to tow your 102 inch wide 1996 Gulf Stream Kingsley 5th wheel trailer a replacement pin box will not offer enough extension. Basically the distance from the back of the truck cab to the center of the king pin when the…

view full answer...

Answer 2

I spoke with a representative from Access. According to them, they do not offer a tonneau cover that is compatible with a low-profile toolbox. If your tool box is something like the TruXedo TonneauMate Truck Bed Toolbox - Crossover Style - Poly Tub…

view full answer...

Answer 3

If you're needing a tonneau cover that sits inside the bed rails of your 2021 Ram 3500 6-1/2' bed then you'll want to check out the TruXedo Pro X15 #TX1446901. This is a solid choice for a soft cover and it has a matte black finish that…

view full answer...

Answer 4

Since the UWS Truck Bed Chest - Wedge Series - Offset Lid - Notched Box - 10.4 cu ft #UWS01032 is a wedge-style tool box, the only relevant dimension to determine the compatibility with a roll-up cover is the height of the tool box. Without knowing…

view full answer...

Answer 5

The side rails that attach the TruXedo Pro X15 Soft Tonneau Cover part #TX1446901 for 6-1/2' beds or part #TX1448901 for 8' beds to the bed rails on your 2017 Ram 3500 will stick out 3" from each side. Therefore, the TruXedo Pro X15 will…

view full answer...

Answer 6

For your 2022 GMC Sierra 3500 6-3/4 foot bed Truxedo has the X15 part #TX97FR which was designed to work with the MultiPro tailgate.

view full answer...

Answer 7

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 8

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 9

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Can UWS Truck Bed Toolbox Open on 2016 GMC Sierra 2500 With Tonneau Cover

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching