Is Optronics # BUL52CB Back-Up Lamp Submersible
Question:
I need to mount two lights on my boat trailer to light up the bunkers under water at night. I would imagine white light would be best. I need to know if this is submersible and what is the amp draw at 12 v dc? If this isnt the best choice what would you suggest? I also need a switch to mount on the winch stand This switch will not be submersed. I was planning to tap off of the running lights taking that to the winch stand switch and then feeding the bunker lights. This way any time the running lights are on I will have the option of turning on the bunker lights. Thanks
asked by: Chuck G
Expert Reply:
The # BUL52CB lamp you referenced might work for the purpose you describe, but a bracket like part # BK70BB and grommet, part # A70GB would be needed. You would also need the wiring pigtail, part # A45CB. The lamp draws a minimal .275 amps at 12.8 volts.
The lamp is submersible, but the contacts at the rear where the pigtail plugs in would be vulnerable to moisture. If you decide to go this route, I would recommend keeping the contacts well coated in dielectric grease, part # 11755 to exclude water from the connections.
The # PK34571 switch and # PK25370 protective boot would also work well for you.
Products Referenced in This Question
2-Wire Pigtail for Optronics Backup and Utility Trailer Lights - 2-Prong PL-3 Plug
- Accessories and Parts
- Trailer Lights
- Wiring
- Plugs and Pigtails
- 10 Inch Long
- Two Wire
- Straight Pigtail
- Optronics
more information >
PVC Grommet for 6-1/2" Oval Trailer Tail Lights
- Accessories and Parts
- Trailer Lights
- Mounting Hardware
- Grommet
- 6-1/2 Inch Long
- Oval
- Optronics
more information >
Trailer Light Mounting Bracket for 6-1/2" Oval Trailer Lights, Steel - Black Powder Coat
- Accessories and Parts
- Trailer Lights
- Mounting Hardware
- 6-1/2 Inch Diameter
- Brackets
- Black
- Optronics
more information >
Pollak Toggle Switch Rubber Boot -15/32"-32 Thread
- Accessories and Parts
- Wiring
- Switches
- Toggle Switch Boot
- Pollak
more information >
Pollak Medium-Duty Toggle Switch - SPST- On-Off - 12 Volt - 20 Amp - 11/16" Handle
- Accessories and Parts
- Wiring
- Switches
- Toggle Switch
- Pollak
more information >
Product Page this Question was Asked From
Optronics LED Backup Light for Trucks or Trailers - Submersible - 36 Diodes - Oval - Clear Lens
- Trailer Lights
- Tail Lights
- Backup
- Oval
- Recessed Mount
- Submersible Lights
- LED Light
- 6-1/2L x 2-5/16W Inch
- White
- Optronics
more information >
Continue Researching
- Q&A: Can Factory Brake Controller Be Installed on 2018 Chevy Silverado
- Q&A: Is There a Bolt On Bracket For Safety Chains on a Trailer
- Q&A: Does Miro-Flex LED Trailer Side Marker Light Need Connector
- Q&A: Installing Trailer Brake Controller on 2019 Chevy Silverado 1500
- Q&A: 1/2 X 13 Threads Per Inch Vintage Trailer Wheel Bolts
- Q&A: Maintenance of Dexter Nev-R-Lube Bearings on Airstream Trailer
- Q&A: Can Red Identification Light Bar be Used as Marker & Reverse Lights
- Article: Testing Trailer Brake Magnets for Proper Function
- Article: Trailer Hitch Receiver Sizes
- Article: Trailer Wiring Diagrams
- Article: Trailer Tire Sizing
- Article: 2023 Best Gifts for Outdoor Enthusiasts
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Article: Towing a Trailer? Let's Talk About Brake Controllers