Bulb Replacement Part Numbers for 432400 Peterson Square Trailer Tail Light

Question

Question:

Do you stock replacement bulbs for this unit. Part #s?? Thanks

asked by: J.D. S

0

Expert Reply:

The part numbers for replacement bulbs for the 432400 taillight lens are, A1157B for the stop, turn and taillights. The side marker lamp replacement is A194B.

expert reply by: Robert G

0

Answer 1

To change the bulbs in Peterson trailer tail light #432400 you will first remove the main lens which is held on by 4 screws. The main bulb can be removed by pushing down and rotating the bulb counterclockwise. There is a diagram on the inside of…

view full answer...

Answer 2

If both turn signals blinking at the same time is a new problem that has occurred after the harness had worked fine before, there are a couple of possibilities that may be causing the issue. First, the easiest thing to check are the trailer…

view full answer...

Answer 3

A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…

view full answer...

Answer 4

What you are describing is normally the result one 1 of 3 issues: First, there could be some corrosion in or on the connectors on the vehicle or trailer side or both. Second there could be a bad ground. Bad grounds can cause all sorts of bizarre…

view full answer...

Answer 5

This is likely a ground issue. Ground problems normally show up when there is more draw on a system such as when you have the running lights on and then use another function like a turn signal or brake light. Make sure that the vehicle side and…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Bulb Replacement Part Numbers for 432400 Peterson Square Trailer Tail Light

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching