Will Kodiak Ceramic Brake Pads Fit 2002 EZ Loader Boat Trailer

Question

Question:

Will these pads fit my 2002 ezloader trailer made for Triton 21 foot bass boat?

asked by: John S

0

Expert Reply:

The Kodiak Ceramic Brake Pads with Stainless Steel Backing Plate - 3,500 lbs to 6,000 lbs # K225CPSS should fit your 2002 EZ Loader boat trailer.

The reason I say "should" is because there isn't a way we can verify for certain the brakes you currently have on your '02 EZ Loader. But based on my research it looks likely you had Kodiak brakes that were rated for between 3,500 lbs and 6,000 lbs, which is what these pads are designed to fit.

You will need to try verify that to be certain these will fit. I have added a link to a video install and review for you to check out as well of the Kodiak Ceramic Brake Pads # K225CPSS.

expert reply by: Kyle S

0

Answer 1

I spoke with my contact at Kodiak regarding the Kodiak Disc Brake Caliper Rebuild Kit #KDBC225KIT that you recently purchased. Before installing the rubber sleeve bushings, he recommends placing them in some warm water in order to soften the rubber.…

view full answer...

Answer 2

The side of the Silicone Dust Boot #K225BSSI, that comes with the Rebuild Kit #KDBC225KIT, with the design on the outside ring needs to face in towards the piston while the other side should face the brake pad. I have attached a photo to demonstrate…

view full answer...

Answer 3

Unfortunately, the rubber boot isn't available as a separate item. If you decide to replace the entire master cylinder, I'd be happy to recommend a replacement if you reply with the model of hydraulic brake coupler you have. To clean the…

view full answer...

Answer 4

I can let you know how to determine what disc brakes you need although we do not have any type of database with parts based on year, make and model of trailer and I was unable to find any reference to a model TRSX240. To get the right replacement…

view full answer...

Answer 5

For your 2105 EZ Loader TA102B boat trailer I am going to recommend upgrading to stainless steel parts to help ensure less corrosion and a longer life. First is the Kodiak Trailer Hub for 3,500-lb Axles - 5 on 4-1/2 - Stainless Steel #KH84545S. These…

view full answer...

Answer 6

The tabs on the outer Kodiak Ceramic Brake Pads #K225CP need to be bent to keep them in place on the caliper. This is done in the linked installation video at the 4:35 mark.

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

The "KTC 7600" stamped on the brake pad doesn't look to be a part number, so I can't cross reference it, but we do know you have Kodiak ceramic brake pads. So to determine the correct brake pads, all you need to do is match up…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...