Thread Pitch of Hitch Mounting Bolts on 2005 Hyundai Santa Fe

Question

Question:

The bolt holes on a 05 Santa Fe for trailer hitch are 20 Mm x 1.25 and 22mm x 1.25 not 1.75. Is that correct Thanks

asked by: Ken R

0

Expert Reply:

You are correct. According to Draw-Tite, each frame member has 5 mounting holes with the corresponding mounting nuts welded up into the frame. The forward-most nuts are M12 x 1.25 and the remaining four are M10 x 1.25. I've provided a diagram showing the locations.

expert reply by: Mike L

0

click to enlarge

Answer 1

The weld nuts in your 2012 Hyundai Santa Fe will use Grade 5 bolts that are M10- 1.25 x 30. There is also another bolt, washer, and nut on each side required for the installation of the Curt #C13073. The Draw-Tite Max-Frame Trailer Hitch Receiver -…

view full answer...

Answer 2

Your weld nut issue is a very common problem when installing a hitch on a vehicle that has had a few years on it. The solution is the thread tap like you mentioned. Just pick the correct size tap and take your time with it and you'll be…

view full answer...

Answer 3

For a hitch, I'd recommend going with the Draw-Tite Class III hitch, part #75684 instead of the Curt hitch you mentioned. The Curt hitch warranty requirements state that a stabilizing strap like part #18050 must be used for non trailer loads…

view full answer...

Answer 4

Yes both the Curt Hitch part #C13073 and the Draw Tite part #75684 which fit your 2012 Kia Sorento fit with a full size spare. I'd say the Curt gives easier access to it so it would be what I'd go with.

view full answer...

Answer 5

Absolutely. If the wire brush and WD-40 treatment didn't work, brake out the big guns and hit that frame mounted weld nut with a M10 x 1.25 thread tap. Be sure to spray a generous amount of WD-40 or other spray lubricant up into the weld…

view full answer...

Answer 6

The tow bar, or hitch that you selected, Curt Trailer Hitch Receiver - Custom Fit - Class III, part #C13073, will fit your 2010 Hyundai Santa Fe. I contacted our representative at Curt and he informed me that the Santa Fe they installed part…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Thread Pitch of Hitch Mounting Bolts on 2005 Hyundai Santa Fe

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching