Replacement Mounting Brackets and Hardware for Westin 3 Inch Round Nerf Bars on 2004 Chevy Silverado

Question

Question:

Hello, I was looking online for replacement mounting brackets for my 2004 Chevrolet 2500 HD Extended Cab. It led me to the Replacement Mounting Brackets and Hardware for Westin 3inch Round Nerf Bars Item # 23-232PK on your website. Do you know if these would work for my truck or not?

asked by: Andrew M

0

Expert Reply:

The correct replacement mounting brackets and hardware for your 2004 Chevrolet 2500 HD with the extended cab are dependent on which Westin 3 inch nerf bars you have. The brackets and hardware are custom to the truck as well as the nerf bars.

Use # 25-168PK for Westin Signature Series 3" and Platinum Series Round Step Bars # 25-1680 and # 25-1685
Use # 23-168PK for Westin E-series 3" Step Bars # 23-1680 and # 23-1685

Part # 23-232PK is compatible with Westin E-Series Round Nerf Bars models # 23-2320 and # 23-2325, which are for certain Dodge Ram Pickups, so they would not work for you.

expert reply by: Carla M

0

John

7/11/2020

What mounting kit do I need for a 2005 GMC Sierra 4dr Crew Cab 4x4- for Westin 3 inch round Nerf Bar? (ARC 00003865 is the only number I can find on it)

Reply

Chris R.

7/16/2020

I couldn't 100 percent verify the model based on that number, but from what I could find it appears that they are the Westin E-Series Nerf Bars. Do yours look like part # 23-1950? If so, the correct mounting hardware is part # 23-195PK.

Reply

Answer 1

Thanks for the photos and information! I confirmed with my contact at Westin that you need Replacement Hardware for Westin Signature Series 3" and Platinum Series Round Step Bars #25-168PK. This fits the Westin Signature Series Round Nerf Bars -…

view full answer...

Answer 2

Replacement Mounting Brackets and Hardware for Westin 3" Round Nerf Bars #23-299PK will not fit your 2004 Chevy Silverado 2500 HD. It is difficult to match up the exact mounting kit without knowing the part number or model of your running…

view full answer...

Answer 3

The Nerf Bars that install with the hardware you referenced do attach to the frame, as you can see by the accompanying cut out of the instructions that I added. It is important to note that the Replacement Mounting Brackets and Hardware for Westin…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Installing the Union Tee #AL21838 with your #AL57575 will tie the pressure of the two air bags together. So yes, a shift in a very heavy load like a truck camper will potentially result in air being forced from one into the other. The reason I say…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Sometimes just use of new spring bars can update a weight distribution hitch to match the tongue weight (TW) of a new trailer, but in the case of your Equal-I-zer system, part #EQ37140ET, the highest-rated bars are the 1400-lb set #EQ90-01-1499 that…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

An oil seal like Redline part #9103309 installs in the back side of the hub (the side nearest the trailer's frame) with the sides or "legs" of the seal inserted into the hub's bore. This means that the flat metal surface of the seal…

view full answer...

Answer 12

I think the best way to explain how to install a grease seal like #10-9 is to take a look at the video I have linked. Go to about the 6 minute, 10 second mark. At this point in the video, our installer begins to install the seal in the back of the…

view full answer...

Replacement Mounting Brackets and Hardware for Westin 3 Inch Round Nerf Bars on 2004 Chevy Silverado

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching