Replacement Pins for Bulldog Square 12K Jack

Question

Question:

In the diagram you have for gear kit 500212, it shows the gear pin part number as 1038210. How can I order just this pin as I can’t seem to find it anywhere?

asked by: Shawn

0

Expert Reply:

In order to repair a Bulldog 10K/12K Square Jack like part # BD182500 you must purchase the Replacement Gear Kit for Bulldog Sidewind Jacks w/ 12,000-lb Capacity part # BD500212. The individual replacement parts within the gear kit are no longer available separately from the manufacturer unfortunately.

expert reply by: Conner L

0

Answer 1

I have an option for you, but I spoke to my contact at Bulldog to try and get a replacement cross shaft for you and he said they are not available. He said that you will just need to get a 12 inch long section of 1 inch cold rolled steel and then…

view full answer...

Answer 2

For the Bulldog 12K jack you will need to replace the entire jack with #BD182701 if the inner tube is damaged. The other option if it is not damaged is simply to replace the screw and nut #BD500217 which will replace the inner working of that inner…

view full answer...

Answer 3

I spoke to my contact at Bulldog and he informed me that the Replacement Screw and Nut Kit #BD500217 would work for your 180 Series Bulldog 12k Jack.

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 9

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 10

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Replacement Pins for Bulldog Square 12K Jack

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching