Low Clearance Tire Chain Recommendation for Tesla X with Size 285/35ZR22

Question

Question:

What will fit the 22” wheel. 285/35ZR22? Has anyone use it for their Tesla X 22inch wheel?

asked by: Stephanie L

0

Expert Reply:

The K-Summit tire chains part # TH2004565767 that you referenced are a confirmed fit for the tire size 285/35ZR22 that you referenced. As far as low clearance tire chains for your Tesla X these are definitely the best option as they require the least amount of clearance to fit since they do not drape over the inside of the tire's sidewall.

expert reply by: Jameson C

0

Answer 1

Yes the Konig Self-Tensioning Snow Tire Chains #th2004705265 that you referenced are a confirmed fit for the tire size of 275/45R20 that you have on your 2021 BMW X5.

view full answer...

Answer 2

Good morning! At this time (September 2018) we do not yet have an installation video for the Draw-Tite Max-Frame Trailer Hitch Receiver #76227 on the 2017 Subaru Outback Wagon. I have however attached the complete written instructions that you can…

view full answer...

Answer 3

I recommend the Draw-Tite 2 inch hitch for the 2016 Subaru Outback Wagon part #76227. The Draw-Tite hitch is a no drill installation compared to some of the other hitch options on your vehicle that require drilling holes in the frame. It's also a…

view full answer...

Answer 4

When installing Draw-Tite hitch #76227, once you remove the 7 push pins from the bottom edge of your 2017 Subaru Outback's fascia, look for a tab under both tail lights and open it up with a flathead screwdriver. There are screws in each you need…

view full answer...

Answer 5

The Draw-Tite Max-Frame Trailer Hitch Receiver part #76227 which is a fit for a 2010-2019 Subaru Outback will install via eight total 10mm nuts which are actually reused as they are the factory fasteners for the bumper beam. The most up to date…

view full answer...

Answer 6

To install the Draw-Tite Max-Frame Trailer Hitch Receiver #76227 on your 2018 Subaru Outback you only need a torque wrench capable of more than 50 ft. lbs, which is going to be most of them. I recommend getting one that has a wider range for other…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Low Clearance Tire Chain Recommendation for Tesla X with Size 285/35ZR22

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching