Is Brightness of Prodigy P3 Brake Controller Screen Adjustable

Question

Question:

Controller works perfect but backlight isnt working so have to use a flashlight to see what is on screen

asked by: Robert D

0

Expert Reply:

You might need to set the brightness of the Prodigy P3 part # 90195 to a higher setting. It currently could be set on low which to set it to "normal" or "high" you'd press menu/option button to view setup screen, select brightness using up and down arrows to navigate, select your brightness setting and press okay.

expert reply by: Jameson C

0

click to enlarge

Answer 1

If your Tekonsha Prodigy P3 Trailer Brake Controller #90195 is not powering on, I recommend checking again for any damaged/blown fuses or relays under the hood of your truck. Check specifically for the brake controller fuse, which should be a 30 amp…

view full answer...

Answer 2

If you are getting a blank screen on your Tekonsha Prodigy P3 Brake Controller #90195 you might just need to reset the unit (as simple as that might sound). Try unplugging the controller, waiting for about 15 minutes, and then plugging it back in.…

view full answer...

Answer 3

I have to go off the GM dealership recommendation. If they are saying you need the Hydrastar #HBA-CAM or Dexter #DX35FR adapter module for your factory brake controller to work with your electric over hydraulic brake actuator, then I can't really…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

You do have the option to utilize the air brakes on your 2023 Freightliner Cascadia to control electric trailer brakes using the Hayes Air Actuated Trailer Brake Controller, part #HA100400C. However, we mostly recommend just using an electric brake…

view full answer...

Answer 9

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 10

The P3 brake controller, #90195, will go into a sort of sleep mode after it detects no movement for 15 minutes. While it is on it does not draw very much power. What you can do to make sure it goes to sleep is exit the truck after turning it off,…

view full answer...

Answer 11

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 12

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...