Is the Truxedo Replacement Tonneau Cover Hook and Loop Fastener # TX1115174 Adhesive Backed

Question

Question:

Is this just the velcro with an adhesive backing or is it a plastic strip that slides into a track?

asked by: Michael B

0

Expert Reply:

I went out to our warehouse and measured the Truxedo Shur-Bond hook and loop fastener, # TX1115174, for you. It has a strip of plastic that slides into a track and is 80 inches long by 1-5/16 inches wide. The velcro portion of the strip is 1 inch wide.

My contact informed me that they no longer carry and hook and loop fasteners with adhesive backing.

expert reply by: Robert G

0

Answer 1

Yes the Replacement TruXedo Shur-Bond Velcro Brand Fastener for 6-1/2' Beds -1-5/16" Wide part #TX1115174 that you have looked at does have the elongated slots. When replacing it you will utilize these to get the strips in place and…

view full answer...

Answer 2

The hook piece on a Velcro setup is usually the piece that fails first, especially in a setup like this where the hook piece is attached to the vehicle and would be out in the sun. As long as your truck bed is 6-1/2 feet long and the cover you have…

view full answer...

Answer 3

The Replacement Truxedo Shur-Bond Velcro Brand Fastener, part #TX1117876 is designed to work with TruxSport tonneau covers only. From the photo you sent it looks like you have a Lo Pro tonneau cover on your truck. The correct replacement Velcro for…

view full answer...

Answer 4

We have Truxedo replacement Shur-Bond Velcro strips that are 1 inch wide with the part #TX1117877 which seems to be a better match for what you are in need of since you said you have 1 inch wide Velcro now and the strips you mentioned are 1-1/4 inch…

view full answer...

Answer 5

The Replacement TruXedo Shur-Bond Velcro Brand Fastener for 6-1/2' Beds -1-5/16" Wide #TX1115174 is designed to fit TruXedo Lo Pro or Original Edge tonneau covers. While I can't say for sure whether or not these will fit a Tonno Pro I…

view full answer...

Answer 6

It looks like you have the TruXedo Lo Pro Soft Roll-up Tonneau Cover #TX598101 for a 2014 Ford F-150 with a short 6-1/2 foot bed. Based on that you are on the money with the part you need, which is the Replacement TruXedo Shur-Bond Velcro Brand…

view full answer...

Answer 7

Typically its the loop section of a Velcro strip that wears out before the hook side as the hooks are made of a harder material. The part #TX1115174 that you referenced comes with both sides though.

view full answer...

Answer 8

I spoke with my Truxedo representative, who tells me that they do not offer a replacement velcro brand strip that measures one inch wide. They do offer a strip that is meant for a long bed truck, part #TX1115173 that measures 96 inches long by 1-1/4…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...