Is the Draw-Tite 65068 Compatible with 2019 Chevrolet Silverado 2500?

Question

Question:

Installed front hitch #65068 on my 2016 Chevy 2500, just traded for a 2019 Chevy 2500, want to install same hitch I got from you #65068 on the 2019. Will it fit? Also will need another Fastener Kit. If it fits, can I get another Fastener Kit? Thanks

asked by: Andy H

0

Expert Reply:

Good news! The Draw-Tite # 65068 that you've previously used on your 2016 Chevy Silverado 2500 is also compatible with your 2019 Chevy Silverado 2500, so you will be able to swap it out without issue- the new part number is the Draw-Tite # 65078, in the event that you ever need to find a front hitch compatible with these two vehicles.

In order to get new mounting hardware you'll want to use the Replacement Hardware Kit # RHK and on that page you'll enter the model number of the hitch you're using- in this case it's # 65078 (the new part number, since the old one is no longer available). This will give you the appropriate replacement hardware for the Draw-Tite hitch and allow you to easily swap vehicles.

I've linked our installation video for this front mounted hitch to this answer for you to use during installation if you need it.

expert reply by: Erik B

0

Answer 1

The front ends of the Silverados and Sierras like your 2018 GMC 2500 are a bit different but the fascia trimming required is the same as you can see in the two attached pictures when installing front hitch #65078. Basically a hole gets cut through…

view full answer...

Answer 2

If you wanted to mount a generator in the Torklift Lock and Load Generator Carrier at the front of a truck like your 2019 Ford F-250 you'd just need a front hitch installed on the truck. For that you'd just need the Draw Tite part #65076 and…

view full answer...

Answer 3

The lid of the Bright Way Trailer Breakaway ICU Kit with 12V, 5-Amp-Hour Battery, Charger, and Wire Loom #BW94FR that you referenced has a wiring diagram shown that details how it wires. Not seen is there is a single wire that runs up to running…

view full answer...

Answer 4

Yep, you're 100 percent correct. For your 2015 Chevy Silverado 2500, the correct EcoHitch front hitch is indeed the one you referenced, which is the following part number: - EcoHitch Invisi Front Mount Trailer Hitch Receiver #306-X7906

view full answer...

Answer 5

You didn't say what was confusing so to elaborate Curt, the manufacturer of front mount receiver #C31071, says that trimming of the front air dam may be required on the 2015 GMC Sierra 2500 Denali. The trimming will need to be around where the…

view full answer...

Answer 6

Hey Dave, so the best option for carrying your carbon frame bike and e-bike is the Swagman Escapee part #S39SR with the ramp #S59SR . It has the capacity for carrying an e-bike, is rated for travel trailer use, only touches the bikes by the tires…

view full answer...

Answer 7

RVs in general have a much rougher ride quality than vehicles due to the less sophisticated suspension (mostly trailer) but also the much longer length between the rear axle of the motorhome and the rear bumper. This exaggerates the movement from…

view full answer...

Answer 8

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 9

The front mounted hitch receiver that will provide you the most amount of ground clearance on your 2016 Chevrolet Silverado 1500 is the Curt Custom Fit 2 Inch Hitch, #C31069. This hitch measures 9.52 inches from the frame mounting flange to the…

view full answer...

Answer 10

The tow hooks on your 2015 Chevrolet Silverado 3500 do not need to be removed to install the Draw-Tite Front Mount Trailer Hitch Receiver part #65078. The bolts that hold the tow hooks do get removed but only to set the trailer hitch in place as they…

view full answer...