Does A Fresh Water Tank Use A Valve Body Like Valterra Bladex Valve

Question

Question:

Are rv cable drain valve grey and fresh water 1 1/2 inch the same Cable drain valve

asked by: Dennis

0

Expert Reply:

The Valterra Waste valves like part # T1001VPM that are 1-1/2" in diameter are different than your fresh water drain. The fresh water is a small drain with a wing nut that drains the fresh water tank. If you can clarify what you are trying to figure out I am happy to assist further.

expert reply by: Heather A

0

Answer 1

In regards to an electric over hydraulic actuator, the 1,000 psi model is for drum brakes and the 1,200 psi model is for disc brakes. The size of the axle, etc. are not factors. The most popular option we offer is the HydraStar Vented Marine Electric…

view full answer...

Answer 2

I confirmed the compatibility of your 2012 Ford F-150 with integrated controller and the HydraStar EOH Acutator for Drum Brakes #HBA-10 with my technical contact at HydraStar. You will not need the #HBA-CAM or an aftermarket controller to use this…

view full answer...

Answer 3

The bolts required to install the Demco 50-Degree A Frame Trailer Coupler #DM13205-95 are 3/8" diameter x 1-3/4" long Grade 5 bolts. I spoke with the manufacturer and they confirmed that you won't want to use Grade 8 bolts on this…

view full answer...

Answer 4

Thanks for that photo, I do appreciate it. And all of the couplers we have - and indeed all the ones I am aware of - require a frame that is fully engaged. While Demco was not able to provide a dimensional drawing, we did measure the Demco 50-Degree…

view full answer...

Answer 5

The 50 degree a-frame trailer angle is the standard angle for a-frame trailers so it would be almost guaranteed that this Demco Coupler part #12660-97SP would fit perfectly. I don't have a way to open your picture but as long as the frame members…

view full answer...

Answer 6

Yes, you will be able to replace your stock coupler with the Demco 50-Degree A-Frame Trailer Coupler #DM13205-95 as long as you have a standard a-frame trailer. I attached a picture below of the dimensions below so you can see if it would work for…

view full answer...

Answer 7

The bolts required to install the Demco 50-Degree A Frame Trailer Coupler #DM13205-95 are 3/8" diameter x 1-3/4" long Grade 5. Grade 8 is not recommended as they don't flex enough and could sheer off.

view full answer...

Answer 8

I spoke with Demco, and they were able to let me know that the: -Demco 50-Degree A-Frame Trailer Coupler w/ Jack Hole #12660-97SP measures 11-1/4" from the center of the ball to the center of the jack hole.

view full answer...

Answer 9

The Demco EZ latch couplers like the part #DM13205-95 have a mechanism that will release when under tension like you are wanting and will allow the trailer to be jacked up and off the ball as well. This would be a great option.

view full answer...

Answer 10

Yes, so long as you have a standard a-frame trailer you will be able to replace your current welded on coupler with the Demco 50-Degree A-Frame Trailer Coupler w/ Jack Hole - eZ-Latch - Zinc - 2-5/16" Ball - 21K item #DM13205-95. I have attached…

view full answer...

Answer 11

In order to install the Demco A-Frame Trailer Coupler #DM13205-95 you'll need to remove the current one on your Primetime Avenger. This is a bolt-on coupler so the welding won't be necessary.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Does A Fresh Water Tank Use A Valve Body Like Valterra Bladex Valve

Product Page this Question was Asked From

Continue Researching