City Water Inlet Valve for Motorhome

Question

Question:

Water Inlet Valve Ace 2016 30.1 model. Might you have this ?? Mine is leaking like crazy

asked by: Loren

0

Expert Reply:

We definitely have water inlets that will work for your 2016 Ace to fix that leak, but you'll need to know the size and thread type on your city water inlet. The reason for that is because there isn't a way to know every part used on every year of every motorhome - that data isn't kept anywhere, and with so many parts, the sheer volume of a list like that would be overwhelming.

What I can tell you is the most likely candidate, which is the JR Products City Water Fill and Check Valve - 1/2" MPT - Chrome # 3729690-200-023 which has an outside diameter of 3 inches, requires a 1-1/2 inch diameter cut out, has a 1-11/16 inch valve depth, and the valve is a 1/2 inch MPT (male pipe thread).

I have added a link to a video review of this water inlet, as well as a link to our entire selection of inlets in case you need one of a different size.

expert reply by: Kyle S

0

click to enlarge

Answer 1

Yes, the 2-Wire RV Propane Gas and Carbon Monoxide Detector, #RS54FR has two different mounting brackets to select from allowing coverage of the existing hole from previous installs. Please note the attached product review video.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

For your race trailer with aluminum roof panels it will seal on the edges with a Butyl Tape #AL64UV. Then you will use either a Non-Sag #AL33KV or Self-Leveling #AL68KV sealant to seal the mounting screws and edges of the aluminum roof panels to…

view full answer...

Answer 5

Although I would not be able to speak on the installation of the part(s) you received for your trailer, I can tell you that the TremPro 644 Silicone Sealant part #0160297 will do an excellent job of sealing your new aluminum panel to the trailer and…

view full answer...

Answer 6

We do have an option for a drain hose to be used with the Valterra Waste Valve for RV Gray Water Tank w/ Cap #T1001D. When installing the Valterra Waste Valve for RV Gray Water Tank w/ Cap #T1001D, you will want to use some Valterra ABS Solvent…

view full answer...

Answer 7

To replace the U-Bolt kit on your 5.2K axles I recommend the following kit: - Replacement U-Bolt Axle Mounting Hardware Kit #LC27XV This comes with U-Bolts for 3" diameter axles, the mounting plate, and the hardware needed to get everything…

view full answer...

Answer 8

I was not able to find anything with the LM38166 part number provided. The RV City Water Inlet with Brass Check Valve #37262145 fits a 1-1/2" diameter cutout and has a 1/2" MPT fitting. We also have this with a 1/2" FPT fitting if that…

view full answer...

Answer 9

The LaSalle Bristol Utopia RV Bathroom Faucet part #34420373P21 fits a pretty standard mounting pattern. That said, if you want to confirm it will fit your exact sink just measure the mounting holes. They should be around a 13/16" diameter with…

view full answer...

Answer 10

The Solera 13.5' Slider (Slide-Topper) in White w/ White Hardware #LCV000163300 is 162 inches wide and has a box width range of 152 to 157-3/4 inches including the flange so this will be the right size slide-topper for your 154-1/4 inch slide out…

view full answer...

City Water Inlet Valve for Motorhome

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching