Rebuild Kit for Fulton 5000 lb Square Jack

Question

Question:

Would like to rebuild my Fulton 5000 jack. I think I would need the gear kit. The shear pin that goes through the handle into the gear continuously breaks.

asked by: Jon H

0

Expert Reply:

The gear kit part # BD500156 that you referenced is the correct bevel gear kit for your Fulton 5000 jack that you sent in a picture of. Then for a bearing kit you'd need the part # BD500224 as well which I attached an install video for too.

expert reply by: Jameson C

0

click to enlarge

Answer 1

It depends on which Bulldog powered A-frame trailer jack you have. For example, #BD500200. has a cap on top and you can use a socket wrench and socket to manually crank the jack up and down. Jacks #BD500187 and #BD500188 come with a handle. But both…

view full answer...

Answer 2

Alghough the Demco #8705001 which we sell as part #DM72VR is meant to be bolted on, it can certainly be welded in place. Because of the zinc plating, you'll want to be sure to do your welding outdoors or in a well-ventilated area. If you MIG or…

view full answer...

Answer 3

I went out to our warehouse for you to double check, the Replacement Bearing for etrailer and Ram Round, Topwind Jacks part #TJA-2000-BR has an I.D. of .50" and an O.D. of 1.025".

view full answer...

Answer 4

Absolutely! I reached out to my contact at Fulton and for your Fulton 2840025 you will need the following parts: Gear Kit #BD500106 Bearing Kit #BD500224 Replacement Handle Kit #BD500171 Replacement Cap #BD500205 The handle kit that was originally on…

view full answer...

Answer 5

Yes, there is 15 teeth per each gear on the Replacement Gear Kit for etrailer and Ram Sidewind Jacks #TJA-2000S-GR. These gears have a thickness of 0.5", an OD of 1.36", and an ID of 0.5".

view full answer...

Answer 6

I see that you got the Replacement Cap for etrailer and Ram Square, Sidewind Jacks #TJD-7000S-CP, which indicates that you have a square side crank jack. I have listed the square jack thrust bearings that we have below, along with their OD/ID, we do…

view full answer...

Answer 7

The Replacement Bearing for etrailer and Ram Round, Topwind Jacks #TJA-2000-BR has an inner diameter of 0.5", an outer diameter of 1.025", and a thickness of .477". When you go to install this bearing, you'll want to put the thrust…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 12

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Rebuild Kit for Fulton 5000 lb Square Jack

Products Referenced in This Question

Featured Help Information

Miscellaneous Media

Continue Researching